Cedar Summit F25720 Скачать руководство пользователя страница 19

Страница: 19 / 108

If there are any missing or damaged pieces or you need assistance with

assembly please contact the consumer relations department directly. Call us

before going back to the store.

STOP

Key Number:

The first two digits represent the step

number. The third digit represents the piece. Note

that if the part is used in multiple steps then the

number only reflects the first step it is used in.

Quantity

Key Number

Part Description,

Part Size

2X 012 Post 2 x 4 x 83”

Step 1: Inventory Parts - Read This Before Starting Assembly

Read the assembly manual completely, paying special attention to ANSI warnings;

notes; and safety/maintenance information on pages 1 - 6.

Before you discard your cartons fill out the form below.

• The carton I.D. stamp is located on the end of each carton. The tracking number is

located on the Cedar Summit ID Plaque (9320357).

• Please retain this information for future reference. You will need this information if you

contact the Consumer Relations Department.

• Please refer to Page 6 for proper hardware assembly.

• Each step indicates which bolts and/or screws you will need for assembly, as well as

any flat washers, lock washers, t-nuts or lock nuts.

This is the time for you to inventory all your hardware, wood and accessories,

referencing the parts identification sheets. This will assist you with your assembly.

• The wood pieces will have the key number stamped on the ends of the boards.

Organize the wood pieces by step, as per the key numbering system below.

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 4)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 5)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 6)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 1)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 2)

CARTON I.D. STAMP: __ __ __ __ __ 14459 ___ (Box 3)

MODEL NUMBER:

F25720

TRACKING NUMBER (from ID Plaque):

+31 20 305 8620

[email protected]

For online parts replacement visit https://parts.kidkraft.eu/

[email protected]

Содержание F25720













































































































Результаты поиска

Содержание F25720

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit F25720, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F25720

Отзывы:

Бренды по названию

Популярные бренды