Cedar Summit Creston Lodge Скачать руководство пользователя страница 43

Страница: 43 / 70

[email protected]

Fig. 17.2

Fig. 17.3

2718

Outside View

1/2”

Hinge Stop

Hardware

On the outside of the (2718) Door Window Panel attach the second Door Handle at approximately the same

place as the one on the inside. Use 2 (S13) #6 x 5/8” Pan Screws. (fig. 17.2)

On the opposite side of the Door Handle measure 5/8” from the top and bottom of (2718) Door Window Panel

attach 2 Door Hinges on the outside using 3 (S13) # 6 x 5/8” Pan Screws per Hinge. (fig. 17.2 and 17.4)

Note:

Hinge stops must be tight to (

2718) Door Window Panel. (fig. 17.3)

8 x

#6 x 5/8” Pan Screw

S13

Other Parts

1 x Door Handle

2 x Door Hinge

Top View

S13

Door
Handle

Step 17: Attach Door Components
Part 2

Using 12- #6 x 5/8" Pan Screws, attach hinges to Door & Fort.

5/8”

Fig. 17.4

Door
Hinge

S13

Содержание Creston Lodge







































































Результаты поиска

Содержание Creston Lodge

Отзывы:

Похожие инструкции для Creston Lodge

Бренды по названию

Популярные бренды

Cedar Summit Creston Lodge, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Creston Lodge

Отзывы:

Похожие инструкции для Creston Lodge

Бренды по названию

Популярные бренды