manualshive.com logo in svg

Cedar Summit Creston Lodge, Инструкция по установке и эксплуатации

Поделиться
Скачать
Cedar Summit Creston Lodge Скачать руководство пользователя страница 28

 

28 

[email protected]

SCALE:1:50

WEIGHT: 

SIZE

SHEET 1 OF 1

REV.

DWG.  NO.

Details

Use 5- #8 x 7/8" Truss to attach  4 -#8 x 7/8" to attach Flanges to

wall panel 

( first, install middle screw at top of Window)

Use 4 -#8 x 7/8" Truss Screws to attach Transom & Half Wall Insert (Attach to grooves in panel)

SCALE:1:50

WEIGHT: 

SIZE

SHEET 1 OF 1

REV.

DWG.  NO.

Details

Use 5- #8 x 7/8" Truss to attach  4 -#8 x 7/8" to attach Flanges to

wall panel 

( first, install middle screw at top of Window)

Use 4 -#8 x 7/8" Truss Screws to attach Transom & Half Wall Insert (Attach to grooves in panel)

Step 11:  How to Install Inserts - Window and Wall Inserts 
Part 1

There is 2 (2720) Lower Window Inserts, 2 (2719) Upper Window Inserts, 1 (2665) Half Wall Insert, 2 (649A) Short 

Half Walls and 1 MOD 3-Pane Transom provided with the Main Clubhouse and Swing.  Depending on which fort 
you have purchased determines where they are installed, see Fort Guide.  See below for how to attach each insert.

When installing you will need the following:

For (2720) Lower Window Insert and (2719) Upper Window Insert - 9 x (S0) #8 x 7/8” Truss Screws per insert.

For (2665) Half Wall Insert, (649A) Short Half Wall and MOD 3-Pane Transom - 4 x (S0) #8 x 7/8” Truss Screws 
per insert.

2719

2720

2719

2720

Tight

and

and

S0

S0

S0

Inside View

Содержание Creston Lodge







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды