Cedar Summit Creston Lodge Скачать руководство пользователя страница 16

Страница: 16 / 70

[email protected]

SCALE:1:50

WEIGHT:

Base 1 -Panel Connect

SHEET 7 OF 9

REV.

DWG. NO.

SIZE

Important! Build on flat surface

1 x

End Panel Assembly 1-1/4 x 42 x 87”

Wood Parts

2622

Hardware

8 x

1/4 x 2-1/2” Wafer Lag

WL5

Back

Side Wall

2618

Swing Side

Front

Step 2: Frame Assembly
Part 2

Place (2622) End Panel Assembly between both (2618) Front Back Panels noticing the panel orientations.

The tops and bottoms of the panels should be flush. Make sure the panels are square then using the pilot

holes as a guide pre-drill with a 3/16” drill bit and fasten the back (2618) Front Back Panel to (2622) End Panel

Assembly and (2622) End Panel Assembly to the front (2618) Front Back Panel with 4 (WL5) 1/4 x 2-1/2” Wafer

Lags per side. (fig. 2.4)

WL5

Fig. 2.4

2622

Notice back (2618)
Front Back Panel
overlaps (2622) End
Panel Assembly

Notice (2622) End
Panel Assembly
overlaps front (2618)
Front Back Panel

Содержание Creston Lodge







































































Результаты поиска

Содержание Creston Lodge

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit Creston Lodge, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Creston Lodge

Отзывы:

Бренды по названию

Популярные бренды