Cedar Summit Creston Lodge Скачать руководство пользователя страница 27

Страница: 27 / 70

Step 10: How to Install Inserts - Upper and Lower Jambs

There are 2 (2601) Lower Jambs and 1 (2602) Upper Jamb provided with the Main Clubhouse and Swing.

Depending on which fort you have purchased determines where they are installed on the (2622) End Panel

Assembly or (2618) Front Back Panel, see Fort Guide. See below for different variations and how to attach the
Jambs to the Panel.

When installing you will need 2 Jamb Mounts per Jamb and 4 x (S0) #8 x 7/8” Truss Screws per Jamb Mount.

Details

SHEET 1 OF 9

SIZE DWG. NO.

REV.

SCALE:1:50

WEIGHT:

Pre-drill using 3/16" drill bit for 1/4 x 2½ Lags

Use #8 x 7/8" Truss screws for the Jamb Mounts

Do not cover the 2 holes with Jamb Mounts

Details

SHEET 1 OF 9

SIZE DWG. NO.

REV.

SCALE:1:50

WEIGHT:

Pre-drill using 3/16" drill bit for 1/4 x 2½ Lags

Use #8 x 7/8" Truss screws for the Jamb Mounts

Do not cover the 2 holes with Jamb Mounts

17”

9-5/8”

17”

Do not cover holes
with Jamb Mount

2601

2602

Jamb
Mount

x 4 per
Jamb
Mount

Jamb
Mount

x 4 per
Jamb
Mount

2601

2602

2601

2602

Centred

Outside View

Inside View

Grooves to
the inside

This variation for Creston
Lodge and Lewiston Retreat
only (TNR III Tube Slide
installation location)

Notice
orientation of
this bracket.
Used in this
variation only.

Содержание Creston Lodge







































































Результаты поиска

Содержание Creston Lodge

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit Creston Lodge, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Creston Lodge

Отзывы:

Бренды по названию

Популярные бренды