Cattron CANplus CP750-E Скачать руководство пользователя страница 38

Страница: 38 / 51

CANplus CP750-E

Control Panel Operation Manual

*Patent Pending

9M02-1000-A501-EN

Revision B

11.3.2 Battery Circuit Requirements

CAUTION

IMPROPER WIRING CAN CAUSE ELECTRICAL NOISE OR UNRELIABLE OPERATION AND MAY

DAMAGE THE CONTROL SYSTEM OR OTHER COMPONENTS. ALL POWER CONNECTIONS

MUST BE FREE FROM FOREIGN MATERIALS, INCLUDING PAINT, WHICH MAY INTERFERE WITH

PROPER CONNECTION. A RELIABLE 30 A MAXIMUM FUSED POWER CIRCUIT MUST BE

PROVIDED FOR THE CONTROL SYSTEM. CATTRON RECOMMENDS THE POWER

CONNECTION BE MADE DIRECTLY TO THE BATTERY WITH THE FUSE ELECTRICALLY CLOSE

TO THE BATTERY. GROUNDING THROUGH FRAME MEMBERS IS NOT RECOMMENDED. ALL

CIRCUIT PATHS MUST BE CAPABLE OF CARRYING ANY LIKELY FAULT CURRENTS WITHOUT

DAMAGE. DO NOT REVERSE THE BATTERY POLARITY. ATTEMPTING TO CRANK THE ENGINE

WHEN THE POLARITY OF THE BATTERY CONNECTIONS IS REVERSED MAY DAMAGE THE

CONTROL SYSTEM.

11.3.3 Battery Positive Connection

The electronic control system operates on either 12 VDC or 24 VDC electrical systems. The unswitched battery

positive connection to the control system is made at the weatherproof connector. The control system provides

switched positive battery protected by solid-state MOSFETs. These outputs include integral protection against

overloads and short circuits.
Powering the control system through a 30 A fused dedicated circuit reduces the possibility of system damage.

CAUTION

DISCONNECTING THE BATTERY WHILE THE ENGINE IS RUNNING MAY RESULT IN DAMAGE TO

ELECTRICAL COMPONENTS. WHEN USING A BATTERY DISCONNECT SWITCH, CATTRON

RECOMMENDS USING A TWO POLE SWITCH TO DISCONNECT BOTH THE BATTERY AND

ALTERNATOR OUTPUT.

Note:

A maximum of three ring terminals should be connected to a power stud to ensure integrity of the

connection. The use of more than three terminals can cause the connection to become loose.

11.3.4 Voltage Drop

If control system voltage drops below 6 V for more than 0.1 s, the control system may reset, causing the self-test

to reactivate. Resetting the control system is equivalent to quickly turning the key switch to OFF and then back to

run without starting the engine. Voltage drops can be caused by a discharged battery, transients from external

equipment, improper wire sizes, faulty wiring, or nearby lightning strikes.

11.3.5 Suppression of Voltage Transients (Spikes)

CAUTION

Содержание CANplus CP750-E




















































Результаты поиска

Содержание CANplus CP750-E

Отзывы:

Похожие инструкции для CANplus CP750-E

Бренды по названию

Популярные бренды

Cattron CANplus CP750-E, Руководство по эксплуатации

Результаты поиска

Содержание CANplus CP750-E

Отзывы:

Похожие инструкции для CANplus CP750-E

Бренды по названию

Популярные бренды