Carrier TruVu TV-MPCXP1628-NR Скачать руководство пользователя страница 59

Страница: 59 / 94

Adjusting the TV-MPCXP1628-NR driver properties

TruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

Installation and Start-up Guide

Trends

Error Rate Trend

—

Total number of errors within the interval time on this network,

including break errors, framing errors, etc..

Packet Rate Trend

—

BACnet/ARCNET data packets transmitted through router,

not the total utilization.

Port S1 Statistics

when used for MSTP

Error Counters

UART Errors

—

UART receive and transmit errors such as break errors, framing

errors, parity errors, and overrun errors.

Invalid Frames

—

Received MS/TP frames that contain an error such as CRC.

Dropped Packets

—

Dropped receive and transmit frames. These may be dropped

due to buffer allocation failures, length errors, or APDU timeouts (in the case of

transmit frames)

Dropped Tokens

—

Dropped tokens that have been retransmitted.

No responses

—

Messages that did not receive a response from the destination

device.

Activity Counters

BACnet/MSTP Rx

Packets

—

BACnet/MSTP data packets received by the TV-

MPCXP1628-NR.

BACnet/MSTP Tx

Packets

—

BACnet/MSTP data packets transmitted by the TV-

MPCXP1628-NR.

Latency

Average Value (milliseconds)

—

The average time from when a packet is queued to

be transmitted until it is actually transmitted on the bus.

Maximum Value (milliseconds)

—

The maximum time from when a packet is

queued to be transmitted until it is actually transmitted on the bus

Trends

Error Rate Trend

—

Total number of errors within the interval time on this network,

including break errors, framing errors, etc.

Packet Rate Trend

—

Percentage of total bus bandwidth used to transmit data

packets.

NOTE

This is for all bus traffic, not just traffic generated by the TV-MPCXP1628-

NR.

Содержание TruVu TV-MPCXP1628-NR































































































Результаты поиска

Содержание TruVu TV-MPCXP1628-NR

Отзывы:

Похожие инструкции для TruVu TV-MPCXP1628-NR

Бренды по названию

Популярные бренды

Carrier TruVu TV-MPCXP1628-NR, Руководство по установке и запуску

Результаты поиска

Содержание TruVu TV-MPCXP1628-NR

Отзывы:

Похожие инструкции для TruVu TV-MPCXP1628-NR

Бренды по названию

Популярные бренды