Carrier RHW036-060 Скачать руководство пользователя страница 1

Страница: 1 / 44

527 01 2701 00

7/2020

Installation Instructions

CONTENTS

Page

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . 1

MODEL NUMBER NOMENCLATURE AND

DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Rated Indoor Airflow . . . . . . . . . . . . . . . . . . . . . . . 2

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Jobsite Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Step 1 — Plan for Unit Location . . . . . . . . . . . . . . 7

• ROOF MOUNT

Step 2 — Plan for Sequence of Unit Installation 7

• CURB-MOUNTED INSTALLATION

• PAD-MOUNTED INSTALLATION

• FRAME-MOUNTED INSTALLATION

Step 3 — Inspect Unit . . . . . . . . . . . . . . . . . . . . . . 7

Step 4 — Provide Unit Support . . . . . . . . . . . . . . 7

• ROOF CURB MOUNT

• SLAB MOUNT (HORIZONTAL UNITS ONLY)

• ALTERNATE UNIT SUPPORT (IN LIEU OF CURB OR

SLAB MOUNT)

Step 5 — Field Fabricate Ductwork . . . . . . . . . . . 9

• FOR UNITS WITH ACCESSORY ELECTRIC

HEATERS

Step 6 — Rig and Place Unit . . . . . . . . . . . . . . . . . 9

• POSITIONING ON CURB

Step 7 — Convert to Horizontal and Connect

Ductwork (when required) . . . . . . . . . . . . . . . 10

Step 8 — Install Outside Air Hood . . . . . . . . . . . 11

• ECONOMIZER HOOD AND TWO-POSITION

DAMPER HOOD PACKAGE REMOVAL AND SETUP

(FACTORY OPTION)

• ECONOMIZER AND TWO-POSITION HOOD

Step 9 — Units with Hinged Panels Only . . . . . 12

Step 10 — Install External Condensate Trap

and Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 11 — Make Electrical Connections . . . . . . 12

• FIELD POWER SUPPLY

• UNITS WITH FACTORY-INSTALLED NON-FUSED

DISCONNECT

• ALL UNITS

• CONVENIENCE OUTLETS

• FACTORY OPTION THRU-BASE CONNECTIONS

• UNITS WITHOUT THRU-BASE CONNECTIONS

• FIELD CONTROL WIRING

• THERMOSTAT

• HEAT ANTICIPATOR SETTINGS

• COMMERCIAL DEFROST CONTROL

• ELECTRIC HEATERS

• SINGLE POINT BOXES AND SUPPLEMENTARY

FUSES

• SINGLE POINT BOXES WITHOUT FUSES

• LOW-VOLTAGE CONTROL CONNECTIONS

• CONTROL AND POWER WIRING DIAGRAMS

EconoMi$er X (Factory Option) . . . . . . . . . . . . . 26

• ECONOMIZER MODULE WIRING DETAILS

• S-BUS SENSOR WIRING

• CO2 SENSOR WIRING

• INTERFACE OVERVIEW

• SETUP AND CONFIGURATION

• TIME-OUT AND SCREENSAVER

• CHECKOUT

• TROUBLESHOOTING

Controller Options . . . . . . . . . . . . . . . . . . . . . . . . 36

• LOW AMBIENT

Smoke Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . 36

• COMPLETING RETURN AIR SMOKE SENSOR

INSTALLATION

• ADDITIONAL APPLICATION DATA

Step 12 — Adjust Factory-Installed Options . . . 37

• SMOKE DETECTORS

• ECONOMI$ER IV OCCUPANCY SWITCH

Step 13 — Install Accessories . . . . . . . . . . . . . . 37

Step 14 — Fan Speed Set Up . . . . . . . . . . . . . . . 38

• UNITS WITH ELECTRO-MECHANICAL CONTROLS

Typical Unit Piping . . . . . . . . . . . . . . . . . . . . . . . . 40

START-UP CHECKLIST. . . . . . . . . . . . . . . . . CL-1

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service,

maintenance, or use can cause explosion, fire, electrical

shock or other conditions which may cause personal injury

or property damage. Consult a qualified installer, service

agency, or your distributor or branch for information or

assistance. The qualified installer or agency must use

factory-authorized kits or accessories when modifying this

product. Refer to the individual instructions packaged with

the kits or accessories when installing.

Follow all safety codes. Wear safety glasses and work

gloves. Use quenching cloths for brazing operations and

have a fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions attached to

the unit. Consult local building codes and appropriate

national electrical codes (in USA, ANSI/NFPA70, National

Electrical Code (NEC); in Canada, CSA C22.1) for special

requirements.

It is important to recognize safety information. This is the

safety-alert symbol

. When you see this symbol on the

unit and in instructions or manuals, be alert to the potential

for personal injury.

Understand the signal words DANGER, WARNING,

CAUTION, and NOTE. These words are used with the

safety-alert symbol. DANGER identifies the most serious

hazards which

will

result in severe personal injury or death.

WARNING signifies hazards which

could

result in personal

injury or death. CAUTION is used to identify unsafe

practices, which

may

result in minor personal injury or

RHW036-060

Single Package Rooftop Heat Pump

with R-410A Refrigerant and

Optional Electric Heat

Содержание RHW036-060













































Результаты поиска

Содержание RHW036-060

Отзывы:

Carrier RHW036-060, Руководство по установке, Страница: 1 / 44

Результаты поиска

Содержание RHW036-060

Отзывы: