Carrier RHW036-060 Скачать руководство пользователя страница 11

Страница: 11 / 44

527 01 2701 00

Specifications subject to change without notice.

Step 8 — Install Outside Air Hood

ECONOMIZER HOOD AND TWO-POSITION DAMPER

HOOD PACKAGE REMOVAL AND SETUP

(

FACTORY

OPTION)
NOTE: Economizer and two-position damper are not avail

able as factory installed options for single phase (-3 voltage

code) models.

The hood is shipped in knock-down form and must be field

assembled. The indoor coil access panel is used as the

hood top while the hood sides, divider and filter are pack

aged together, attached to a metal support tray using plastic

stretch wrap, and shipped in the return air compartment be

hind the indoor coil access panel. The hood assembly’s

metal tray is attached to the basepan and also attached to

the damper using two plastic tie

wraps.

1. To gain access to the hood, remove the filter access

panel. (See Fig. 9.)

Fig. 9 — Typical Access Panel Locations

2. Locate the (2) screws holding the metal tray to the

basepan and remove. Locate and cut the (2) plastic

tie-wraps securing the assembly to the damper. (See

Fig. 10.) Be careful to not damage any wiring or cut

tie-wraps securing any wiring.

Fig. 10 — Economizer and Two-Position Damper

Hood Parts Location

3. Carefully lift the hood assembly (with metal tray)

through the filter access opening and assemble per

the steps outlined in the following section

Econo

mizer Hood

and Two-Position Hood.

ECONOMIZER AND TWO-POSITION HOOD
NOTE: If the power exhaust accessory is to be installed on

the unit, the hood shipped with the unit will not be used and

must be discarded. Save the aluminum filter for use in the

power exhaust hood assembly.

1. The indoor coil access panel will be used as the top

of the hood. Remove the screws along the sides and

bottom of the indoor coil access panel. See Fig. 11.

Fig. 11 — Indoor Coil Access Panel Relocation

2. Swing out indoor coil access panel and insert the

hood sides under the panel (hood top). Use the

screws provided to attach the hood sides to the hood

top. Use screws provided to attach the hood sides to

the unit. See Fig. 12.

Fig. 12 — Economizer Hood Construction

3. Remove the shipping tape holding the economizer

barometric relief damper in place (economizer only).

4. Insert the hood divider between the hood sides. See

Fig. 12 and 13. Secure hood divider with 2 screws on

each hood side. The hood divider is also used as the

bottom filter rack for the aluminum filter.

5. Open the filter clips which are located underneath the

hood top. Insert the aluminum filter into the bottom fil

ter rack (hood divider). Push the filter into position

past the open filter clips. Close the filter clips to lock

the filter into place. See Fig. 13.

6. Caulk the ends of the joint between the unit top panel

and the hood top.

7. Replace the filter access panel.

FILTER ACCESS PANEL

OUTDOOR-AIR OPENING AND
INDOOR COIL ACCESS PANEL

COMPRESSOR
ACCESS PANEL

HOOD PARTS

PLASTIC TIE WRAP
QTY (2)

SCREWS FOR METAL TRAY
QTY (2)

TOP
PANEL

INDOOR
COIL
ACCESS
PANEL

CAULK
HERE

TOP
PANEL

INDOOR COIL
ACCESS PANEL

19 1/16”

SCREW

HOOD DIVIDER

LEFT
HOOD
SIDE

33 3/8”

(848mm)

(483mm)

Содержание RHW036-060













































Результаты поиска

Содержание RHW036-060

Отзывы:

Carrier RHW036-060, Руководство по установке, Страница: 11 / 44

Результаты поиска

Содержание RHW036-060

Отзывы: