manualshive.com logo in svg

Carrier RHW036-060, Руководство по установке, Страница: 2 / 44

Поделиться
Скачать
Carrier RHW036-060 Скачать руководство пользователя страница 2

2

Specifications subject to change without notice.

2

product and  property damage.  NOTE  is used  to highlight

suggestions  which 

will

  result  in  enhanced  installation,

reliability, or operation.

MODEL NUMBER NOMENCLATURE AND 

DIMENSIONS

See  Fig.  1  for  RHW  model  number  nomenclature.  See

Fig. 2 on pages 4 - 6) for unit dimensional drawings.

Rated Indoor Airflow

Table  1  lists  the  rated  indoor  airflow  used  for  the AHRI

efficiency rating for the units covered in this document.

Table 1 — Rated Indoor Airflow

WARNING

Electrical  shock  can  cause  personal  injury  and  death.

Shut off all power to this equipment during installation.

There may be more than one disconnect switch. Tag all

disconnect locations to alert others not to restore power

until work is completed.

WARNING

UNIT OPERATION AND SAFETY HAZARD

Failure to follow this warning could cause personal inju

-

ry, death and/or equipment damage.

R-410A refrigerant systems operate at higher pressures

than standard R-22 systems. Do not use R-22 service

equipment  or  components  on  R-410A  refrigerant

equipment.

WARNING

PERSONAL INJURY AND ENVIRONMENTAL

HAZARD

Failure to follow this warning could cause personal injury

or death.

Relieve pressure and recover all refrigerant before sys

-

tem repair or final unit disposal.

Wear safety glasses and gloves when handling refriger

-

ants. Keep torches and other ignition sources away from

refrigerants and oils.

CAUTION

PERSONAL INJURY HAZARD

Failure  to  follow  this  caution  may  result  in

personal injury.

Sheet metal parts may have sharp edges or burrs. Use

care  and  wear  appropriate  protective  clothing,  safety

glasses and gloves when handling parts and servicing

air conditioning equipment.

MODEL NUMBER

RATED INDOOR AIRFLOW (cfm)

RHW036

1200

RHW048

1500

RHW060

2000

Содержание RHW036-060













































Отзывы:

Нет отзывов