Carrier RHW036-060 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 44

Carrier RHW036-060 Скачать руководство пользователя страница 43

527 01 2701 00

Specifications are subject to change without notice.

CL-1

START-UP CHECKLIST

RHW036-060 Single Package Rooftop Heat Pump Units

(Remove and use for job file)

I. PRELIMINARY INFORMATION

MODEL NO _____________________________________________
JOB NAME _____________________________________________
SERIAL NO _____________________________________________
ADDRESS _____________________________________________
START-UP DATE ________________________________________
TECHNICIAN NAME ______________________________________
ADDITIONAL ACCESSORIES
_____________________________________________________________________________________________________

II. PRE-START-UP

Verify that all packaging materials have been removed from unit

(Y/N) _____

Verify installation of outdoor air hood

(Y/N) _____

Verify that condensate connection is installed per instructions

(Y/N) _____

Verify that all electrical connections and terminals are tight

(Y/N) _____

Check that indoor-air filters are clean and in place

(Y/N) _____

Check that outdoor air inlet screens are in place

(Y/N) _____

Verify that unit is level

(Y/N) _____

Verify that fan assembly is free of obstructions and rotor spins freely

(Y/N) _____

Verify that scroll compressors are rotating in the correct direction

(Y/N) _____

Verify installation of thermostat

(Y/N) _____

III. START-UP

ELECTRICAL

Supply Voltage

L1-L2_____________

L2-L3_____________

L3-L1_____________

Compressor Amps 1

L1 _____________

L2 _____________

L3 _____________

Compressor Amps 2

L1 _____________

L2 _____________

L3 _____________

Supply Fan Amps

L1 _____________

L2 _____________

L3 _____________

Outdoor Fan Amps

L1 _____________

L2 _____________

TEMPERATURES

Outdoor-air Temperature

_____________ °F DB (Dry Bulb)

Return-air Temperature

_____________ °F DB

_____________

°

F WB (Wet Bulb)

Cooling Supply Air Temperature

_____________ °F

PRESSURES

Refrigerant Suction

____________ PSIG

Refrigerant Discharge

____________ PSIG

Verify Refrigerant Charge using Charging Charts (Y/N) _____

GENERAL

Economizer minimum vent and changeover settings to job requirements (if equipped) (Y/N) _____
Verify smoke detector unit shutdown by utilizing magnet test (Y/N) _____

NOTE: To avoid injury to personnel and damage to equipment or

property when completing the procedures listed in this start-up

checklist, use good judgment, follow safe practices, and adhere

to the safety considerations/information as outlined in preced

-

ing sections of this Installation Instruction document.

«
...
41
42
43
44
»

Содержание RHW036-060













































Отзывы:

Нет отзывов