Carrier RHW036-060 Скачать руководство пользователя

Страница: 2 / 44

Specifications subject to change without notice.

product and property damage. NOTE is used to highlight

suggestions which

will

result in enhanced installation,

reliability, or operation.

MODEL NUMBER NOMENCLATURE AND

DIMENSIONS

See Fig. 1 for RHW model number nomenclature. See

Fig. 2 on pages 4 - 6) for unit dimensional drawings.

Rated Indoor Airflow

Table 1 lists the rated indoor airflow used for the AHRI

efficiency rating for the units covered in this document.

Table 1 — Rated Indoor Airflow

WARNING

Electrical shock can cause personal injury and death.

Shut off all power to this equipment during installation.

There may be more than one disconnect switch. Tag all

disconnect locations to alert others not to restore power

until work is completed.

WARNING

UNIT OPERATION AND SAFETY HAZARD

Failure to follow this warning could cause personal inju

ry, death and/or equipment damage.

R-410A refrigerant systems operate at higher pressures

than standard R-22 systems. Do not use R-22 service

equipment or components on R-410A refrigerant

equipment.

WARNING

PERSONAL INJURY AND ENVIRONMENTAL

HAZARD

Failure to follow this warning could cause personal injury

or death.

Relieve pressure and recover all refrigerant before sys

tem repair or final unit disposal.

Wear safety glasses and gloves when handling refriger

ants. Keep torches and other ignition sources away from

refrigerants and oils.

CAUTION

PERSONAL INJURY HAZARD

Failure to follow this caution may result in

personal injury.

Sheet metal parts may have sharp edges or burrs. Use

care and wear appropriate protective clothing, safety

glasses and gloves when handling parts and servicing

air conditioning equipment.

MODEL NUMBER

RATED INDOOR AIRFLOW (cfm)

RHW036

1200

RHW048

1500

RHW060

2000

Содержание RHW036-060













































Результаты поиска

Содержание RHW036-060

Отзывы:

Похожие инструкции для RHW036-060

Бренды по названию

Популярные бренды

Carrier RHW036-060, Руководство по установке

Результаты поиска

Содержание RHW036-060

Отзывы:

Похожие инструкции для RHW036-060

Бренды по названию

Популярные бренды