Carrier RHW036-060 Скачать руководство пользователя

Страница: 13 / 44

527 01 2701 00

Specifications subject to change without notice.

option non-fused disconnect switch. Maximum wire size

is #2ga AWG (copper only) per pole on contactors, #2ga

AWG (copper only) per pole on optional disconnect, and

4/0 AWG (copper only, see Fig. 17) per pole on terminal

or fuse blocks on units with single point box (see Fig. 18).

See Fig. 18 and unit label diagram for field power wiring

connections.

NOTE: Unit may be equipped with short test leads (pigtails)

on the field line connection points on contactor C or optional

disconnect switch. These leads are for factory-run test pur

poses only; remove and discard before connecting field

power wires to unit connection points. Make field power

connections directly to line connection pressure lugs only.
UNITS WITH FACTORY-INSTALLED NON-FUSED

DISCONNECT
The factory-installed optional non-fused disconnect (NFD)

switch is located in a weatherproof enclosure located under

the main control box. The manual switch handle and shaft

are shipped in the disconnect enclosure. Assemble the

shaft and handle to the switch at this point. Discard the fac

tory test leads (see Fig. 18).

Fig. 17 — Disconnect Switch and Unit

Connect field power supply conductors to LINE side termi

nals when the switch enclosure cover is removed to attach

the handle.

Fig. 18 — Power Wiring Connections

Field-Install the NFD Shaft and Handle

1. Remove the control box access panel. The NFD

enclosure is located below the control box (see

Fig. 19).

2. Remove (3) cap head screws that secure the NFD

enclosure front cover — (2) on the face of the cover

and (1) on the left side cover. See Fig. 20.

3. Remove the front cover of the NFD enclosure.

4. Make sure the NFD shipped from the factory is at

OFF position (the arrow on the black handle knob is

at OFF).

5. Insert the shaft with the cross pin on the top of the

shaft in the horizontal position. See Fig. 20.

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal in

jury, death, or property damage.

Do not connect aluminum wire between disconnect

switch and unit. Use only copper wire.

COPPER

WIRE ONLY

ELECTRIC

CONNECT

WITCH

ALUMINUM

WIRE

Disconnect

per

NEC

208/230-1-60

Disconnect

per

NEC

208/230-3-60

460-3-60
575-3-60

Units Without Single Point Box or Disconnect Option

Units With Disconnect Option

Optional

Disconnect

Switch

Disconnect factory test leads; discard.

Factory
Wiring

Equip

GR Lug

Ground

(GR)

Equip GR Lug

Ground

(GR)

3 Phase Only

Units With Electric Heat Option with Single Point Box

and Without Disconnect Option

Single Point Box

Factory
Wiring

Equip GR

Lug

Ground (GR)

Terminal Block

— OR —

Single Point Box

Factory
Wiring

Equip GR

Lug

Ground (GR)

Fuse/Terminal Block

Fuse

Содержание RHW036-060













































Результаты поиска

Содержание RHW036-060

Отзывы:

Похожие инструкции для RHW036-060

Бренды по названию

Популярные бренды

Carrier RHW036-060, Руководство по установке

Результаты поиска

Содержание RHW036-060

Отзывы:

Похожие инструкции для RHW036-060

Бренды по названию

Популярные бренды