background image

                                                                                           

 

We are glad that you have chosen a kit of the CM bait boat. 

These are selected high-quality components, of which some are specially made for 

this boat.

 

 
 

The hull is made of ABS, is therefore very light and dimensionally stable and can be easily 

glued or repaired. 

 

 

These instructions are intended to facilitate the assembly, but must be implemented by an 

experienced modeler. Partly it can be that components have to be modified due to 

tolerances or that they have to be installed otherwise. This manual is only intended as a 

suggestion. There are several ways to complete the boat. 

Thus, customers have already developed various models, such as with solar panels, 

charge socket outside or jet drive:

 

  
 

All parts have been tested for their function before shipment. It is important to pay 

attention to the correct connection of the individual components. In addition, the 

instructions for the use of the components must be read carefully and implemented to 

ensure the correct use. For damages that are due to a non-professional use, we assume 

no warranty. 

 
 

Please read this manual and later the operating instructions carefully before you 

start working. 

 
 

Generally, it makes sense to provide all screws with a screw lock. 

 
 

But now nothing should get in the way:

 

 
 
 
 
 
 
 
 
 
 

222

Содержание XXL 2020
























Отзывы: