Carp Madness XXL 2020 страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 23

background image

4. Adjust the controls

The controllers are fully automatic and do not need to be taught.

We recommend to solder the cables firmly to the motors after a successful

adjustment. The screws supplied by us have a left and a right direction.

This is important to allow the best possible directional stability.The direction

of the screws should be installed towards the outside of the boat

Congratulations, now the hull is ready !!!!!!!!!!I<

mportant: the assembled lower shell can now be tested in the water and the

running behavior can be assessed.

14

14

14

«
...
12
13
14
15
16
...
»

Содержание XXL 2020
























Отзывы:

Нет отзывов

Похожие инструкции для XXL 2020

Бренд: BIC Sport Страницы: 12

FLEXIBLE FURLER 2

Бренд: CDI Страницы: 18

expedition series

Бренд: NRS Страницы: 8

35 Express 2006

Бренд: Pro-Line Boats Страницы: 95

Бренд: LaserPerformance Страницы: 16

Бренд: LaserPerformance Страницы: 21

Бренд: Crivit Страницы: 43

Бренд: Baja Страницы: 87

Бренд: NW Explorations Страницы: 59

INT'L SLX W004699

Бренд: Polaris Страницы: 52

Бренд: Gnom Rov Страницы: 27

Бренд: Gumotex Страницы: 52

Бренд: BENETEAU Страницы: 104

Бренд: Sailfish Страницы: 60

Fisherman Series

Бренд: Ranger Страницы: 77

Бренд: Yamaha Страницы: 277

Бренд: Hobie Страницы: 16

Бренд: Hobie Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды