Carmanah SPEEDCHECK 15 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 61

background image

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

59

SPEEDCHECK-15/18 USER MANUAL

11.0 MIAMI DADE COUNTY HARDWARE COMPLIANCE

11.0 Miami Dade County Hardware Compliance

Requirements

SPEEDCHECK-15:

1. Only Top of Pole Mount 74454 may be used with this system. This mount is supplied with 5/8"-11

galvanized steel bolts that meet the requirements of ASTM A307.

2. The cabinet (if present) minimum bolt requirement is for two type 304 or 316 stainless steel 1/2"-13 U-bolts

meeting the requirements of ASTM F593 with a minimum yield strength of 65KSI. Type 304 or 316
stainless steel lock washers shall be used with the U-bolts. The corresponding 1/2" nuts must meet the
requirements of ASTM F594. U-bolts shall be torqued to 90 in-lbs. Cabinet mounts must be used with
these appropriate ½” U-bolts. The display sign must be used with 4-6” OD round pole mount 88419
containing 85483 mounting plates. Display mounts can be used with banding or U-bolts.

3. The standard plastic pole cap must be replaced with the metal 82865 pole cap kit.
4. If a solar system, the system must be used with 80W solar panel and 100Ah battery.

«
...
57
58
59
60
61
»

Содержание SPEEDCHECK 15






























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDCHECK 15

Бренд: Dahua Страницы: 33

Бренд: Com-Net Ericsson Страницы: 20

Cobra CB 29 LX LE

Бренд: Giant Страницы: 6

Бренд: PRESIDENT Страницы: 48

Бренд: Midland Страницы: 6

SIMRAD Navico RT1200

Бренд: Kongsberg Страницы: 21

Бренд: Blaupunkt Страницы: 38

Бренд: Blaupunkt Страницы: 45

Бренд: Blaupunkt Страницы: 167

Бренд: Hyundai Страницы: 28

Бренд: OK. Страницы: 159

Бренд: Panasonic Страницы: 7

Бренд: Panasonic Страницы: 16

Бренд: auna Страницы: 53

Бренд: Nice Страницы: 20

Бренд: Kriesler Страницы: 5

Бренд: Lowrance Страницы: 48

Бренд: Lowrance Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды