Carmanah SPEEDCHECK 15 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 61

background image

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

17

SPEEDCHECK-15/18 USER MANUAL

3.0 COMPONENTS AND PREPARATION

3.5 Overview of Cabinet Connection Terminals

Solar Cabinets

Solar Cabinets with StreetHub™

AC Cabinets

AC Cabinets with StreetHub™

For solar systems without the StreetHub™ monitoring option, ensure the power cable going to

the radar sign is terminated on the Load +/- terminals of the SunSaver charge controller. This will

utilize low voltage disconnect (LVD) protection which will prevent the battery from complete

discharge.

The circled sections contain the StreetHub™ monitoring device connections, including the DC

power out to the radar sign (DC+/- terminals).

Solar and

Battery

Connections

DC power to

radar sign

DC power

from AC/DC

power supply

(pre-wired)

DC power to

radar sign

(Load +/-)

«
...
15
16
17
18
19
...
»

Содержание SPEEDCHECK 15






























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDCHECK 15

Бренд: oticon Страницы: 2

Бренд: Memorex Страницы: 48

Бренд: XHDATA Страницы: 4

Бренд: Noxon Страницы: 20

Бренд: Easy Listener Страницы: 17

Бренд: Comtex Страницы: 24

Бренд: boytone Страницы: 4

Бренд: Microgate Страницы: 11

Бренд: Bush Страницы: 12

Бренд: Bush Страницы: 24

Бренд: Bush Страницы: 24

Бренд: Bush Страницы: 44

Бренд: Hyundai Страницы: 40

Бренд: Heathkit Страницы: 41

Бренд: First Alert Страницы: 29

AN / PRC- 1 04(A)

Бренд: LORAL TERRACOM Страницы: 105

Бренд: G+M Elektronik Страницы: 23

Бренд: Decatur Electronics Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды