Carmanah SPEEDCHECK 15 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 61

background image

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

37

SPEEDCHECK-15/18 USER MANUAL

4.0 INSTALLATION

4.12 Solar Power System Wiring

Before mounting the cabinet to the pole, all wiring internal to the pole (power, LED, optional

StreetHub™ serial and ground cables) should be fished through the pole as applicable.

1.  In-pole wiring: fish solar cable from solar panel down through hole in pole for cabinet nipple.
2.  External wiring: route solar cable through a liquid tight conduit.
3.  Remove battery and solar fuses from fuse holders in cabinet.
4.  Connect solar positive spade terminal (red wire, yellow heat shrink) to the Solar+ fuse holder screw

terminal. Connect solar negative spade terminal (black wire, brown heat shrink) to Solar

−

screw terminal.

5. Connect the sign DC input power wires to one of the following terminals:

a. Load+ and Load- terminals

(red is +, black is −)

b. DC+

and DC− terminals

(StreetHub™ equipped systems only,

red is +, black is −)

6.  Check the battery for voltage (recommended ~12.6V or greater for new installs) and polarity.
7.  Connect the battery to the battery harness ring terminals.
8.  Mate solar panel connectors to solar harness connectors.
9.  Install battery fuse, then solar fuse.
10. Ensure green charging status LED illuminates on solar charge controller indicating proper solar charging.

Ensure cabinet door is fully closed and latched otherwise damage may occur.

Cabinet DC input power

terminals

DC out to radar sign

(StreetHub™ equipped only)

DC out to radar sign

(Load +/- terminals)

«
...
35
36
37
38
39
...
»

Содержание SPEEDCHECK 15






























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDCHECK 15

Бренд: Acconeer Страницы: 34

Бренд: Zebra Страницы: 4

airMAX Bullet Titanium BM2-Ti

Бренд: Ubiquiti Страницы: 24

Бренд: SOUNDMASTER Страницы: 38

Бренд: Quintezz Страницы: 14

Бренд: Gogen Страницы: 28

Бренд: Hytera Страницы: 9

Бренд: Garmin Страницы: 46

MALA MIRAsoft HDR

Бренд: Guideline Geo Страницы: 27

Бренд: Vega Absolute Страницы: 17

Бренд: Midland Страницы: 16

Бренд: Midland Страницы: 18

Бренд: Symbol Страницы: 24

Бренд: Airsmart Technology Страницы: 23

Бренд: Medion Страницы: 192

Бренд: NABO Страницы: 120

Бренд: Vaisala Страницы: 394

Бренд: auna Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды