Carmanah SPEEDCHECK 15 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 61

background image

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

26

SPEEDCHECK-15/18 USER MANUAL

4.0 INSTALLATION

4.4 Quick Change Pole Mount

1. Remove sign face from main enclosure to allow for easier access.
2. Fasten the top bracket to the sign enclosure (Note: Legacy version with angled top shown pictured below.

New version has a flat top.)

3.  Fasten bottom bracket to the sign enclosure.
4.  Loosely secure the top bracket hanger to the pole using hose clamp.
5.  Hang sign enclosure without sign face on top of the top bracket hanger.
6.  Loosely secure the bottom bracket hanger to the pole using hose clamp.
7.  Make fine adjustments for alignment and commissioning (see

).

8. Once the alignment has been validated, secure the brackets to the pole in a more permanent manner

using stainless steel banding (not provided) or U-bolts (an orderable option).

9. Complete installation wiring.
10. Attach sign face.
11. Secure cabinet in place with padlock.

Lower Housing Mounting Bracket

Upper Housing Mounting Bracket

(note legacy angled top version

shown)

Top Bracket Hanger

Installed Top Bracket

Installed Bottom Bracket

«
...
24
25
26
27
28
...
»

Содержание SPEEDCHECK 15






























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDCHECK 15

Бренд: G-RF Страницы: 6

Бренд: Yaesu Страницы: 2

Бренд: Belkin Страницы: 102

Бренд: S&C Страницы: 14

Бренд: XM Satellite Radio Страницы: 58

Бренд: Radio Shack Страницы: 16

Cobra CB 29 LX LE

Бренд: Giant Страницы: 6

HomePatrol - II

Бренд: Uniden Страницы: 43

Бренд: Sangean Страницы: 9

Бренд: Sangean Страницы: 1

Sound Splash FM

Бренд: ION Страницы: 2

Бренд: TechniSat Страницы: 68

DIGITRADIO 370 CD IR

Бренд: TechniSat Страницы: 172

Бренд: TechniSat Страницы: 196

Бренд: Trevi Страницы: 8

Бренд: Trevi Страницы: 28

Бренд: Yaesu Страницы: 43

Бренд: PERFECTPRO Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды