Carmanah SPEEDCHECK 15 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 61

background image

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 |

[email protected]

14

SPEEDCHECK-15/18 USER MANUAL

2.0 SYSTEM OVERVIEW

2.7 Typical Configurations – SPEEDCHECK-15 – Strobe Flashers

Optional strobe kits are supported for SPEEDCHECK-15 only. Strobes kits are an alternative option to using

external beacons (cannot be combined together). There are two strobe kits available:

1. Dual strobe (Blue and Red)
2. Single strobe (White)

Strobe flashers contained in the strobe kits are Whelan TIR3 series and come with various flash patterns. The

white-violet wire controlling flash pattern and gray wire controlling the synchronization option are capped with

heat-shrink in case strobe flash pattern needs to be modified in the field.

See the single page instruction sheet included with each strobe order for reference or consult the Whelan website

for more strobe flasher information.

The standard flash pattern used for strobe kits is “

ComAlert™ 150

”. The SPEEDCHECK-15 Output Function is

set to “

Flash

” and if the dual strobe option is ordered, the synchronization is set to “

Alt B with A

”.

WHITE

BLUE

RED

«
...
12
13
14
15
16
...
»

Содержание SPEEDCHECK 15






























































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDCHECK 15

Бренд: Uniden Страницы: 2

Бренд: TRX Страницы: 28

Бренд: Weelko Страницы: 13

Бренд: Palstar Страницы: 2

Бренд: Radio Shack Страницы: 12

Бренд: Clas Ohlson Страницы: 28

Бренд: PNI Страницы: 132

Бренд: JRC Страницы: 6

Бренд: Vertex Standard Страницы: 4

Бренд: JVCKENWOOD Страницы: 18

Бренд: Vertex Standard Страницы: 44

Marr (South) SRM9030plus

Бренд: Scot-tel Gould Страницы: 2

Бренд: SJ Страницы: 43

Бренд: HIKVISION Страницы: 20

Бренд: Tecnet Страницы: 16

Clatronic DR 795

Бренд: CTC Union Страницы: 46

Бренд: Koden Страницы: 156

Бренд: Laser Atlanta Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды