background image

8200-M535-O1 Rev B 

 225-DS 

TABLE OF CONTENTS 

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 1 
SPECIFICATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 2 
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 3 

Load Cell Cable Connection with RFI Suppression  . . . . . . . . . . . . . . . . . . . . . . .  Page 6 
Load Cell Cable Connection without RFI Suppression  . . . . . . . . . . . . . . . . . . . .  Page 9 
Load Cell Cable Connections with Over 30 Feet of Cable . . . . . . . . . . . . . . . . . .  Page 9 
Sense Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 10 
Dead Load Boost Jumper (DLB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 10 
Gnd to Chassis Jumper  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 10 

INDICATOR SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 11 
CALIBRATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 13 
MULTI-SCALE OPERATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  Page 14 

 

FCC COMPLIANCE STATEMENT 

This equipment generates uses and can radiate radio frequency and if not installed and used 
in accordance with the instruction manual, may cause interference to radio communications.  It 
has been tested and found to comply with the limits for a Class A computing device pursuant 
to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection 
against such interference when operated in a commercial environment.  Operation of this 
equipment in a residential area may cause interference in which case the user will be 
responsible to take whatever measures necessary to correct the interference. 

 

You may find the booklet “How to Identify and Resolve Radio TV Interference Problems” prepared by the 
Federal Communications Commission helpful.  It is available from the U.S. Government Printing Office, 
Washington, D.C. 20402, Stock No. 001-000-00315-4. 

 

All rights reserved.  Reproduction or use, without expressed written permission, of editorial or 
pictorial content, in any manner, is prohibited.  No patent liability is assumed with respect to 
the use of the information contained herein.  
 
 While every precaution has been taken in the preparation of this manual, the Seller assumes 
no responsibility for errors or omissions. Neither is any liability assumed for damages resulting 
from use of the information contained herein.  All instructions and diagrams have been 
checked for accuracy and ease of application; however, success and safety in working with 
tools depend to a great extent upon the individual accuracy, skill and caution.  For this reason 
the Seller is not able to guarantee the result of any procedure contained herein.  Nor can they 
assume responsibility for any damage to property or injury to persons occasioned from the 
procedures.  Persons engaging the procedures do so entirely at their own risk. 

PRECAUTIONS 

 

Before beginning installation of this option card, read this manual and pay 
special attention to all "WARNING" symbols: 

 

  

   

IMPORTANT

 

  

  

   

ELECTRICAL
WARNING 

 

 

  

   

STATIC 
SENSITVE 

 

 

II 

Содержание 225-DS





















Отзывы: