background image

8200-M535-O1 Rev B 

 225-DS 

SPECIFICATIONS 

Number of Scale Inputs: 

Two 

Load Cells: 

Resistive strain gage load cells. 
Up to 16ea, 350 

 load cells total / 24ea 800 

 load cells total 

External Connections: 

Dual 7 position spring cage clamp (24 to 16ga wire) 

Temperature Range: 

14° to 104° F (-10° to +40° C) 

Displayed Resolution: 

100 to 10,000 divisions (commercial) 
240,000 divisions (maximum, non-commercial) 

Internal Resolution: 

16, 777, 216 divisions 

Sample Rate: 

selectable 1 to 100 samples per second   

Auto Zero Range: 

0.5 divisions or 1 through 9 divisions 

Excitation Voltage: 

12.0VDC 

Signal Input Range:  

1.0 mV min. to 40 mV max. (with dead load boost) 

Load Cell Cable Length:   1500 feet maximum.  

Consult factory for other requirements

  

30 feet maximum without sense lines 

Sensitivity:  

NON-COMMERCIAL 
NTEP 
CANADA 
OIML 

 
0.15uV/e 
0.3uV/e (Class III/IIIL) 
0.3uV/e (Class III/IIIHD) 
0.7uV/e (Class III) 

Scale Divisions: 

NON-COMMERCIAL 
NTEP 
CANADA 
OIML 

 
100 to 240,000 
100 to 10,000 (Class III/IIIL) 
100 to 10,000 (Class III/IIIHD) 
100 to 10,000 (Class III) 

Division Value: 

Programmable 

Weighing Units: 

Programmable 

  
 

Содержание 225-DS





















Отзывы: