Instruction manual CM465SS
32
33
Please keep this instruction manual for future reference
Please keep this instruction manual for future reference
Instruction manual CM465SS
7. Once inserted, make sure the two coloured buttons have snapped
back out, otherwise the service door cannot be closed.
»
The two coloured buttons are correctly snapped out (A).
»
The two coloured buttons are not snapped out (B).
8. Replace the drip tray and waste coffee container.
9. Close the service door.
N OT E S :
If the brewing unit is not put in place correctly, the service door cannot
be closed.
If it is difficult to insert the brewing unit, it must be made into the right
height (before inserting) by pressing the brewing unit firmly together
from top and bottom.
If it is still difficult to insert the brewing unit:
»
Leave it out of the appliance, place the drip tray, close the service
door, switch the main switch on the back of the appliance to ‘off’
and then to ‘on’ again.
»
Wait for all the lights to go off, then open the door, remove the
drip tray and replace the brewing unit.
»
Replace the drip tray, together with the grounds container.
»
Close the service door.
EN 30
7. Once inserted, make sure the two red buttons have snapped back
out, otherwise the service door cannot be closed.
•
The two red buttons are correctly snapped out (A).
•
The two red buttons are not snapped out (B).
8. Replace the drip tray and waste coffee container.
9. Close the service door.
Notes
• If the brewing unit is not put in place correctly, the service door
cannot be closed.
• If it is diffi cult to insert the brewing unit, it must be made into the
right height (before inserting) by pressing the brewing unit fi rmly
together from top and bottom.
• If it is still diffi cult to insert the brewing unit:
•
Leave it out of the appliance, place the drip tray, close the
service door, switch the main switch on the back of the appliance
to ‘off’ and then to ‘on’ again.
•
Wait for all the lights to go off, then open the door, remove the
drip tray and replace the brewing unit.
•
Replace the drip tray, together with the grounds container.
•
Close the service door.
Cleaning the milk container
Always clean the tubes inside the milk container when you prepare milk.
If there is still milk in the container, do not leave it out of the refrigerator
for longer than strictly necessary. Clean the container each time you
prepare milk as described in the section “Making cappuccino”.
All components can be washed in a dishwasher, placing them in
the top basket of the dishwasher.
1. Turn the milk container lid clockwise then remove it.
2. Remove the milk spout (S) and intake tube (M).
MAINTENANCE
1 CAPPUCCINO
2 CAFFELA
TTE
S
M
A
B
EN 30
7. Once inserted, make sure the two red buttons have snapped back
out, otherwise the service door cannot be closed.
•
The two red buttons are correctly snapped out (A).
•
The two red buttons are not snapped out (B).
8. Replace the drip tray and waste coffee container.
9. Close the service door.
Notes
• If the brewing unit is not put in place correctly, the service door
cannot be closed.
• If it is diffi cult to insert the brewing unit, it must be made into the
right height (before inserting) by pressing the brewing unit fi rmly
together from top and bottom.
• If it is still diffi cult to insert the brewing unit:
•
Leave it out of the appliance, place the drip tray, close the
service door, switch the main switch on the back of the appliance
to ‘off’ and then to ‘on’ again.
•
Wait for all the lights to go off, then open the door, remove the
drip tray and replace the brewing unit.
•
Replace the drip tray, together with the grounds container.
•
Close the service door.
Cleaning the milk container
Always clean the tubes inside the milk container when you prepare milk.
If there is still milk in the container, do not leave it out of the refrigerator
for longer than strictly necessary. Clean the container each time you
prepare milk as described in the section “Making cappuccino”.
All components can be washed in a dishwasher, placing them in
the top basket of the dishwasher.
1. Turn the milk container lid clockwise then remove it.
2. Remove the milk spout (S) and intake tube (M).
MAINTENANCE
1 CAPPUCCINO
2 CAFFEL
ATTE
S
M
A
B
C L E A N I N G T H E M I L K C O N TA I N E R
Always clean the tubes inside the milk container when you prepare milk.
If there is still milk in the container, do not leave it out of the refrigerator
for longer than strictly necessary. Clean the container each time you
prepare milk as described in the section “Making cappuccino”.
All components can be washed in a dishwasher, placing them
in the top basket of the dishwasher.
1. Turn the milk container lid clockwise then remove it.
2. Remove the milk spout (S) and intake tube (M).
3. Remove the frothed milk regulator (F) by pulling it outwards.
4. Wash all the components thoroughly with hot water and mild
washing-up liquid. Make sure there are no milk residues left inside
the holes (H) and the groove (G) on the fi ne end of the frothed milk
regulator (F).
5. Check that the intake tube and spout are not clogged with milk
residues.
6. Replace the frothed milk regulator, milk spout and intake tube.
7. Replace the milk container lid.
C L E A N I N G T H E N O Z Z L E S
Clean the nozzles on the milk container every time after heating milk or
making cappuccino. Otherwise, remains of milk may set hard.
- Place a container under the milk dispenser pipe and press on the
CLEAN button (N3) on the milk container for at least 5 seconds. The
display shows “CLEANING”!
Warning! Risk of scalding from steam and hot water escaping
from the milk dispenser pipe.
EN 31
3. Remove the frothed milk regulator (F) by pulling it outwards.
4. Wash all the components thoroughly with hot water and mild
washing-up liquid. Make sure there are no milk residues left inside
the holes (H) and the groove (G) on the fi ne end of the frothed milk
regulator (F).
5. Check that the intake tube and spout are not clogged with milk
residues.
6. Replace the frothed milk regulator, milk spout and intake tube.
7. Replace the milk container lid.
Cleaning the nozzles
Clean the nozzles on the milk container every time after heating milk or
making cappuccino. Otherwise, remains of milk may set hard.
• Place a container under the milk dispenser pipe and press on the
CLEAN button (N3) on the milk container for at least 5 seconds.
The display shows “CLEANING”!
Warning! Risk of scalding from steam and hot water escaping from the milk dispenser pipe.
MAINTENANCE
G
F
H
H
N3
EN 31
3. Remove the frothed milk regulator (F) by pulling it outwards.
4. Wash all the components thoroughly with hot water and mild
washing-up liquid. Make sure there are no milk residues left inside
the holes (H) and the groove (G) on the fi ne end of the frothed milk
regulator (F).
5. Check that the intake tube and spout are not clogged with milk
residues.
6. Replace the frothed milk regulator, milk spout and intake tube.
7. Replace the milk container lid.
Cleaning the nozzles
Clean the nozzles on the milk container every time after heating milk or
making cappuccino. Otherwise, remains of milk may set hard.
• Place a container under the milk dispenser pipe and press on the
CLEAN button (N3) on the milk container for at least 5 seconds.
The display shows “CLEANING”!
Warning! Risk of scalding from steam and hot water escaping from the milk dispenser pipe.
MAINTENANCE
G
F
H
H
N3