Instruction manual CM465SS
30
31
Please keep this instruction manual for future reference
Please keep this instruction manual for future reference
Instruction manual CM465SS
EN 29
MAINTENANCE
Cleaning the inside of the coffee maker
• Check regularly (about once a week) that the inside of the appliance
is not dirty. If necessary, remove coffee deposits with a sponge.
• Remove the residues with a vacuum cleaner.
Cleaning the brewing unit
The brewing unit must be cleaned regularly to avoid the build-up of
coffee encrustations which could cause malfunction.
The brewing unit can only be taken out when the appliance is
switched off by pressing the on/
off
button
under the control
panel
. Otherwise, the coffee machine may be seriously
damaged
Proceed as follows:
1.
T urn the appliance off by pressing the on/
off
button (
do
not switch
off the main switch or unplug) and wait for the display
to go off.
2.
Open the service door.
3.
Remove the drip tray and the waste coffee container.
4.
Press the two red release buttons inwards and at the same time pull
the brewing unit outwards
Clean the brewing unit under running tap water without using
detergent. Never clean the brewing unit in the dishwasher.
Do not use washing up liquid to clean the brewing unit. It would
remove the lubricant applied to the inside of the piston.
5.
Soak the brewing unit in water for about 5 minutes, then rinse.
6.
After cleaning, replace the brewing unit by sliding it onto the
internal support (S) and pin (P) at the bottom, then push the PUSH
symbol fully in until it clicks into place.
Note:
If the brewing unit i
s difficult t
o insert, you must first adapt
it to the right dimensions by pressing it forcefully from the bottom
and top.
P
S
EN 29
MAINTENANCE
Cleaning the inside of the coffee maker
• Check regularly (about once a week) that the inside of the appliance
is not dirty. If necessary, remove coffee deposits with a sponge.
• Remove the residues with a vacuum cleaner.
Cleaning the brewing unit
The brewing unit must be cleaned regularly to avoid the build-up of
coffee encrustations which could cause malfunction.
The brewing unit can only be taken out when the appliance is
switched off by pressing the on/
off
button
under the control
panel
. Otherwise, the coffee machine may be seriously
damaged
Proceed as follows:
1.
T urn the appliance off by pressing the on/
off
button (
do
not switch
off the main switch or unplug) and wait for the display
to go off.
2.
Open the service door.
3.
Remove the drip tray and the waste coffee container.
4.
Press the two red release buttons inwards and at the same time pull
the brewing unit outwards
Clean the brewing unit under running tap water without using
detergent. Never clean the brewing unit in the dishwasher.
Do not use washing up liquid to clean the brewing unit. It would
remove the lubricant applied to the inside of the piston.
5.
Soak the brewing unit in water for about 5 minutes, then rinse.
6.
After cleaning, replace the brewing unit by sliding it onto the
internal support (S) and pin (P) at the bottom, then push the PUSH
symbol fully in until it clicks into place.
Note:
If the brewing unit i
s difficult t
o insert, you must first adapt
it to the right dimensions by pressing it forcefully from the bottom
and top.
P
S
TO R E M OV E T H E D R I P T R AY:
1. Open the service door.
2. Remove the drip tray and the waste coffee container.
3. Clean the drip tray and waste coffee container.
4. Replace the drip tray and waste coffee container.
5. Close the service door.
C L E A N I N G T H E WAT E R TA N K
1. Clean the water tank regularly (about once a month) with a damp
cloth and a little mild washing up liquid.
2. Remove all traces of washing up liquid.
C L E A N I N G T H E S P O U T S
1. Clean the nozzles periodically using a sponge.
2. Check regularly that the holes in the coffee spout are not blocked. If
necessary, remove coffee deposits with a toothpick.
Milk residues left on the nozzle and in the container may
impact the correct operation of the appliance.
Each time you use the coffee maker, they must therefore be removed by
cleaning the nozzle with a sponge.
C L E A N I N G T H E P R E - G R O U N D C O F F E E F U N N E L
- Check regularly (about once a month) that the pre-ground coffee funnel
is not blocked.
EN 28
MAINTENANCE
To remove the drip tray
:
1. Open the service door.
2. Remove the drip tray and the waste coffee container.
3. Clean the drip tray and waste coffee container.
4. Replace the drip tray and waste coffee container.
5. Close the service door.
Cleaning the water tank
1. Clean the water tank regularly (about once a month) with a damp
cloth and a little mild washing up liquid.
2. Remove all traces of washing up liquid.
Cleaning the spouts
1. Clean the nozzles periodically using a sponge.
2. Check regularly that the holes in the coffee spout are not blocked.
If necessary, remove coffee deposits with a toothpick.
Milk residues left on the nozzle and in the container may
impact
the
correct operation of the appliance.
Each time you use the coffee maker, they must therefore be
removed by cleaning the nozzle with a sponge.
Cleaning the pre-ground coffee funnel
• Check regularly (about once a month) that the pre-ground coffee
funnel is not blocked.
N
C L E A N I N G T H E I N S I D E O F T H E C O F F E E M A K E R
- Check regularly (about once a week) that the inside of the
appliance is not dirty. If necessary, remove coffee deposits
with a sponge.
- Remove the residues with a vacuum cleaner.
C L E A N I N G T H E B R E W I N G U N I T
The brewing unit must be cleaned regularly to avoid the build-up of coffee encrustations which
could cause malfunction.
The brewing unit can only be taken out when the appliance is switched off by
pressing the on/off button under the control panel. Otherwise, the coffee machine
may be seriously damaged
Proceed as follows:
1. Turn the appliance off by pressing the on/off button (
do not switch
off the main switch or unplug
) and wait for the display to go off.
2. Open the service door.
3. Remove the drip tray and the waste coffee container.
4. Press the two red release buttons inwards and at the same time pull
the brewing unit outwards
Clean the brewing unit under running tap water without using
detergent. Never clean the brewing unit in the dishwasher.
Do not use washing up liquid to clean the brewing unit. It
would remove the lubricant applied to the inside of the piston.
5. Soak the brewing unit in water for about 5 minutes, then rinse.
6. After cleaning, replace the brewing unit by sliding it onto the internal
support (S) and pin (P) at the bottom, then push the PUSH symbol fully
in until it clicks into place.
N OT E :
If the brewing unit is difficult to insert, you must first adapt it to the right
dimensions by pressing it forcefully from the bottom and top.
