Canon PowerShot G3 Скачать руководство пользователя

Страница: 76 / 310

Chapter 2: Service Error Codes

2-16

Cause

Remedy

##107

[ RX ] The transmitting machine cannot use fall-

back

• Ask the operator of the other party to in-

crease the transmission level

so that the

signal may be received correctly.

• Adjust the NL equalizer

so that the sig-

nal may be received correctly.

• Loosen the RTN transmission conditions

so that RTN will not be transmitted.

• Provide echo remedy 2

• Decrease the transmission level

so that

an echo of the transmitted signal will not
be received.

• The line condition is poor, and the signal

from the other party cannot be received
correctly even at 2400 bps.

• The machine malfunctioned because of an

echo.

Cause

Remedy

##108

[

] Reversal of the polarity has been detected in

relation to F-NET2 (Facsimile
communication network services 2)

[Japanese model]

• Divide the documents so that a single trans-

mission will consist of 31 or fewer.

• Divide the document so that each signal is

shorter than 2 A4 sheets.

• Transmit once again.

• File a problem report with NTT.

• An attempt was made to send 32 or more

documents at a time.

• The length of a single document is longer

than 2 A4 sheets (594 mm).

• The other party released the line while in

reception.

• STOC has detected a fault.
• An account charge pulse occurred.

Содержание PowerShot G3






















































































































































































































































































































Результаты поиска

Содержание PowerShot G3

Отзывы:

Похожие инструкции для PowerShot G3

Бренды по названию

Популярные бренды

Canon PowerShot G3, Список кодов ошибок

Результаты поиска

Содержание PowerShot G3

Отзывы:

Похожие инструкции для PowerShot G3

Бренды по названию

Популярные бренды