Canon PowerShot G3 страница 48 Скачать руководство пользователя

Страница: 48 / 310

Chapter1: User Error Codes

1-35

Cause

Remedy

#101

[

] Call cannot be made

• Reverse L1 and L2 of the line.

• The polarity of L1 and that of L2 of the

line do not match.

Cause

Remedy

#102

[ TX/RX ] Subaddress or password does not match

during an ITU-T-compliant subaddress
communication

• Match the subaddress and password of the

machine with those of the other party.

• Ask the operator of the other party to set

an appropriate subaddress and password.

• Ask the operator of the other party to de-

lete image data that is no longer needed,
and transmit once again.

• The subaddress and the password of the

machine do not match that of the other
party.

• An appropriate subaddress and password

are not set on the other party.

• In the case of transmission, the image

memory of the party is full.

Содержание PowerShot G3






















































































































































































































































































































Результаты поиска

Содержание PowerShot G3

Отзывы:

Похожие инструкции для PowerShot G3

Бренды по названию

Популярные бренды

Canon PowerShot G3, Список кодов ошибок

Результаты поиска

Содержание PowerShot G3

Отзывы:

Похожие инструкции для PowerShot G3

Бренды по названию

Популярные бренды