Canon PowerShot G3 страница 14 Скачать руководство пользователя

Страница: 14 / 310

Chapter1: User Error Codes

1-1

Cause

Remedy

Cause

Remedy

#001

[

] Document has jammed

• Remove the document, and try again.

• Using a copying machine, make an A4/LTR

copy of the document to transmit.

• If too small or thin, use a carrier sheet

(document cover) to transmit.

• Correct it by referring to the Service

Manual of the model in question.

• The document is trapped in the feeder.

• The document is not of a standard size or

thickness.

• An internal mechanism is faulty.

#002

[

] Document is shorter than indicated

• The document is shorter than the length

indicated in [minimum] of [sheet dimen-
sions] given as specifications in the Ser-
vice Manual of the model in question.

• Use a carrier sheet (document over) to

transmit.

• Using a copying machine, make an A4/LTR

copy of the document to transmit.

Содержание PowerShot G3






















































































































































































































































































































Результаты поиска

Содержание PowerShot G3

Отзывы:

Похожие инструкции для PowerShot G3

Бренды по названию

Популярные бренды

Canon PowerShot G3, Список кодов ошибок

Результаты поиска

Содержание PowerShot G3

Отзывы:

Похожие инструкции для PowerShot G3

Бренды по названию

Популярные бренды