Canon DR 7090C - imageFORMULA - Document Scanner Скачать руководство пользователя | Manualshive

Страница: 64 / 129

background image

5-5

Chapter 5 Maintenance

Cleaning the Flatbed (Platen Glass) and
Pressure Board

A dirty flatbed (platen glass) or pressure board can cause
soiling of scanned images, or document size detection errors.
Clean the flatbed (platen glass) and pressure board
periodically.

1.

Open the feeder.

CAUTION

Open the feeder carefully and slowly, taking care to avoid letting
the feeder fall over backwards.

2.

Wipe the flatbed (platen glass), scanning glass
(narrow strip of glass) and pressure board with a
cloth moistened with plain water and thoroughly
wrung out. Next, wipe the flatbed (platen glass),
scanning glass and pressure board with a soft, dry
cloth.

«
...
62
63
64
65
66
...
»

Содержание DR 7090C - imageFORMULA - Document Scanner


































































































































Отзывы:

Нет отзывов

Похожие инструкции для DR 7090C - imageFORMULA - Document Scanner

Бренд: Datecs Страницы: 73

Бренд: Datamax Страницы: 12

E-Class Mark II

Бренд: Datamax Страницы: 40

Бренд: Datamax Страницы: 46

Бренд: Fargo Страницы: 6

Бренд: Fargo Страницы: 90

Бренд: Fargo Страницы: 126

Бренд: FARGO electronics Страницы: 278

Бренд: VASTEX Страницы: 15

4250 - WorkCentre - Copier

Бренд: Xerox Страницы: 4

Phaser 3100MFP/S

Бренд: Xerox Страницы: 56

Бренд: Graphic Products Страницы: 28

DocuPrint 96 IPS Series

Бренд: Xerox Страницы: 101

Бренд: Jolimark Страницы: 64

Бренд: Oki Страницы: 9

All in One Printer

Бренд: Epson Страницы: 210

aculaser cx37 series

Бренд: Epson Страницы: 261

AL-MX200 Series

Бренд: Epson Страницы: 410

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды