Canon DR 7090C - imageFORMULA - Document Scanner Скачать руководство пользователя | Manualshive

Страница: 28 / 129

background image

2-6

Chapter 2 Setup

4.

Connecting the Scanner to the Computer

There are two methods for connecting the DR-7090C scanner to a computer: a USB connection to a standard USB port built in to
the computer, or SCSI connection to a SCSI card installed in an expansion slot of the computer. Select the method that is best suited
to your computer environment.

Interface Connector Locations

The USB port and SCSI connector are located on the scanner
as shown below.

IMPORTANT

• Do not connect both USB and SCSI cables to the scanner at the

same time.

• Use only the supplied power cord.
• The scanner and computer should both be turned OFF when

making connections.

• Make sure that the computer is turned OFF before connecting the

SCSI cable. The scanner may not be properly recognized by the
computer if it is connected while the computer is turned ON.

• A SCSI cable is not supplied with the scanner. Obtain a cable with

connectors that match the SCSI connectors on both the scanner
and the computer.

Using a USB Connection

1.

Connect the supplied power cord into the power
connector on the back of the scanner.

a

2.

Connect the power cord into an AC outlet.

b

3.

Use the supplied USB cable to connect the scanner
to the computer.

Connect the square plug (Type B) of the USB cable to the
scanner.

WARNING

When using a USB connection, make sure to set the SCSI
terminator to ON. If the SCSI terminator is set to OFF, proper
scanning may not be possible.

SCSI ID, terminator

USB Connector

SCSI Connector

120 V model Type

220 - 240 V model Type

Type A

Type B

«
...
26
27
28
29
30
...
»

Содержание DR 7090C - imageFORMULA - Document Scanner


































































































































Отзывы:

Нет отзывов

Похожие инструкции для DR 7090C - imageFORMULA - Document Scanner

Бренд: Canon Страницы: 29

PIXMA MX410 Series

Бренд: Canon Страницы: 46

Бренд: Canon Страницы: 65

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 2

Sure shot 80 tele

Бренд: Canon Страницы: 39

BJC6500 - BJC 6500 Color Inkjet Printer

Бренд: Canon Страницы: 6

Бренд: Canon Страницы: 20

imagePROGRAF iPF6450

Бренд: Canon Страницы: 35

PIXMA MX340 Series

Бренд: Canon Страницы: 11

PIXMA MX340 Series

Бренд: Canon Страницы: 16

imagePROGRAF iPF6300S

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 19

Бренд: Canon Страницы: 101

iP4700 - PIXMA Color Inkjet Printer

Бренд: Canon Страницы: 28

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды