Canon CP660 Скачать руководство пользователя страница 347

Страница: 347 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 10 TROUBLESHOOTING

10-65

Cause

Rollers
(duplexing unit)

Feeding guide

Reversing
roller,
Duplexing
feeding roller

Drive gear

Sensor lever

Step

Yes/No

YES

Action

Remove the paper lint
and dust.

Remove any foreign
matter. If burrs are
found, replace the
feeding guide.

If worn or deformed,
replace the roller.

Replace the worn or
cracked gear.

Position the sensor
lever correctly so that it
moves smoothly. If
damaged or deformed,
replace it.

Replace the duplexing
unit.

Checks

Are the rollers inside the duplexing
unit coated with paper lint or dust?

Is there foreign matter or burrs on
the feeding guide?

Is the reversing roller or the duplex-
ing feeding roller worn or deformed?

Is the drive gear worn or cracked?

Is any sensor lever damaged or
deformed?

Duplexing Unit

Download free service manual at http://printer1.blogspot.com

Содержание CP660























































































































































































































































































































































































































Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды

Canon CP660, Руководство по обслуживанию

Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды