Canon CP660 Скачать руководство пользователя страница 345

Страница: 345 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 10 TROUBLESHOOTING

10-63

C. After executing test printing in service mode, the leading edge of print paper jams at

a location after the secondary transfer belt.

Cause

Separation
sensor (PS5)

Fixing roller
drive gear

Fixing assem-
bly inlet guide,
Fixing/separa-
tion upper
guide,
Fixing/separa-
tion lower
guide

Upper fixing
roller, Lower
fixing roller

Fixing/delivery
sensor
(PS1903) lever

Fixing/delivery
sensor
(PS1903)

Fixing delivery
roller

Step

Yes/No

YES

Action

Go to step 2.

Go to step 4.

If damaged or
deformed, replace the
lever or the spring.
Position the spring cor-
rectly.

Replace the sensor.

Replace the worn or
cracked drive gear.

Clean the parts as nec-
essary.

Clean the upper fixing
roller or the lower fixing
roller.

Replace the rollers as
necessary.

Replace the damaged
or worn lever. Position
the spring correctly.

Replace the sensor.

If the fixing /delivery
roller is worn, replace
it.

Checks

Does the leading edge of print paper
reach the fixing roller?

Is the separation sensor lever or
spring damaged or deformed? Is the
spring of the sensor lever dis-
placed?

Replace the separation sensor. Is
the problem corrected?

Is the fixing roller drive gear worn or
cracked?

Is the fixing assembly inlet guide,
fixing/separation upper guide, or fix-
ing/separation lower guide soiled,
scratched, or coated with toner?

Is the upper fixing roller or the lower
fixing roller soiled or coated with
toner?

Is the upper fixing roller or the lower
fixing roller deformed or damaged?

Is the fixing/delivery sensor dam-
aged or worn? Is the spring of the
sensor lever displaced?

Replace the fixing/delivery sensor. Is
the problem corrected?

Download free service manual at http://printer1.blogspot.com

Содержание CP660























































































































































































































































































































































































































Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды

Canon CP660, Руководство по обслуживанию

Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды