Canon CP660 Скачать руководство пользователя страница 145

Страница: 145 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

CHAPTER 4 IMAGE FORMATION SYSTEM

4-47

3. Removing the Pre-Transfer

Charging Assembly from the
Intermedate Transfer Drum

1) Remove the two screws, and detach

the secondary pre-transfer charging
assembly from the intermediate trans-
fer drum.

Screws

Secondary pre-transfer charging

assembly

Figure 4-827

Note:

1. Be sure to place the intermediate

transfer drum on a level surface.
Use paper under the drum.

2. Do not clean the intermediate trans-

fer drum. If absolutely necessary,
wipe its surface with a flannel cloth
moistened with water, and then dry
wipe it.

4. Color Cartridge and Print Image

Faults
Normally, the color toner cartridges (Y,

M, C) may be taken out and put back in
easily. If any of them cannot be moved at
all because of a power fault or the like,
perform the following:

1) Open the front cover.
2) Perform the steps on p. 3-15 to

remove the side cover.

3) Disengage the four claws, and remove

the stopper arm cover.

Claws

Stopper arm cover

Figure 4-828

Download free service manual at http://printer1.blogspot.com

Содержание CP660























































































































































































































































































































































































































Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды

Canon CP660, Руководство по обслуживанию

Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды