Canon CP660 Скачать руководство пользователя страница 229

Страница: 229 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

4) Remove the two screws, and pull out

the connector; then, pull out the lead
wire.

Screw

Connector

Lead wire

Figure 6-326

5) Remove the screw, and remove the

heater metal fixing; then, pull out the
lower heater slowly.

Screw

Heater metal fixing

Lower heater

Figure 6-327

10. Removing the Upper Fixing Roller
1) Perform the steps on p. 6-1 to remove

the upper fixing heater.

2) Perform steps 2) through 5) on p. 6-12

to remove the upper thermistor.

3) Perform steps 2) through 5) on p. 6-16

to remove the lower fixing heater.

4) Pull up the releasing lever to remove;

then, slide the releasing lever in the
direction of the arrow to detach.

Screw

Releasing lever

Figure 6-328

CHAPTER 6 FIXING SYSTEM

6-17

When securing the lead wire terminal
of the fixing heater or the like with a
screw, take care not to subject the lead
wire to excess force.

Points to Note When Mounting

Download free service manual at http://printer1.blogspot.com

Содержание CP660























































































































































































































































































































































































































Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды

Canon CP660, Руководство по обслуживанию

Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды