Canon CP660 Скачать руководство пользователя страница 89

Страница: 89 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

5) Remove the two screws, and detach

the heat discharge fan 3 together with
the fan duct.

Screws

Fan duct

Figure 3-522

6) Remove the seven screws, and

detach the right cover.

Screws

Right cover

Figure 3-523

9. Multifeeder Tray
1) Open the multifeeder tray.
2) Slide the sub tray of the multifeeder

tray, and disengage the two claws
used to secure the tray in place.

Claws

Figure 3-524

3) Disconnect the connector, and

remove the multifeeder tray.

Connector

Multifeeder tray

Figure 3-525

CHAPTER 3 LASER EXPOSURE SYSTEM

3-19

When removing the pre-exposure
LED assembly, take care not to apply
excess force to the pre-exposure
LEDs.

Caution

Download free service manual at http://printer1.blogspot.com

Содержание CP660























































































































































































































































































































































































































Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды

Canon CP660, Руководство по обслуживанию

Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды