Canon CP660 Скачать руководство пользователя страница 223

Страница: 223 / 407

CANON 660/2100 REV.0 FEB. 1999 PRINTED IN JAPAN (IMPRIME AU JAPON)

2. Removing the Fixing Assembly

1) Open the delivery cover.
2) Shift the two fixing assembly locking

levers and the releasing lever in the
direction of the arrows; then, lift the
fixing assembly slightly, and detach it
to the front.

Fixing assembly locking lever

Releasing lever

Fixing assembly

Figure 6-302

3. Mounting a New Fixing Assembly
1) Prepare a new fixing assembly, and

detach the two spacers (orange).

Figure 6-303

2) Place the fixing assembly on the

guide as shown.

Figure 6-304

3) Push the fixing assembly until it butts

against the rear end of the printer unit.

Figure 6-305

CHAPTER 6 FIXING SYSTEM

6-11

If the duplexing unit is mounted, be
sure to remove it before removing the
fixing assembly.

Caution

Download free service manual at http://printer1.blogspot.com

Содержание CP660























































































































































































































































































































































































































Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды

Canon CP660, Руководство по обслуживанию

Результаты поиска

Содержание CP660

Отзывы:

Похожие инструкции для CP660

Бренды по названию

Популярные бренды