background image

3

The Cannon appliance is warranted against defects in materials

and workmanship for a period of one, (1) year from its date of

original purchase, for residential use in Australia.

Warranty service, which includes parts and labour for the replace-

ment or repair of defective parts, is available through Cannon

Authorised Service Agencies. (Please refer to the list of authorised

service agents in this manual.)

Consumers are responsible for service person’s travel outside nor-

mal service areas (approximately seventy (70k) radius from the

nearest Cannon dealer’s location), local cartage, and normal main-

tenance as described in this manual.

Any product subjected to misuse, abuse, negligence, accident or

alteration will have its warranty voided.  The defacement of serial

plate will have its warranty voided.

If installation is not carried out in accordance with manufacturer’s

instructions, this warranty may be void.

The customer must keep their “Tax Invoice” as proof of purchase of

this product, and compliance certificate as proof of required instal-

lation.

Model number: ______________________________________

Serial number: _______________________________________

Date of manufacture: _________________________________

Date installed: _______________________________________

Compliance Certificate No: ____________________________

Warranty

Don’t risk your appliance warranty

Only a licensed person will give you a Compliance Certifi-

cate, showing that the work complies with all the relevant

standards.

And only a licensed person will have insurance protecting

their workmanship for 6 years.

So make sure you use a licensed person to install this appli-

ance and ask for your Compliance Certificate to ensure the

manufacturers appliance warranty will be honoured.

22

Notes

Содержание FITZP

























Отзывы: