FASCIA REMOVAL / INSTALLATION
Removing Fitzroy Fascia (refer FIG 18a)
1. Remove the wire mesh guard by gently lifting it
upwards and then outwards. Similarly remove a fitted
glass kit by also gently lifting it upwards and then
outwards.
2. Remove 4 M5 screws fixing the fascia assembly to the
heater body. Bring the bottom of the fascia towards
you gently to partly disengage it from the body of the
heater. After it has been disengaged gently lift it up
vertically to completely disengage it from the body of
the heater.
the PCB connector and unclip the cable from the clipping
points. The cable is routed through a plastic grommet
which will have to be removed from the base panel.
Refer
FIG 19
.
Inner Glass Removal
To remove the inner glass loosen off all the clamp screws
and completely remove the upper clamps and one
vertical side. Try not to touch the front surface of the glass.
To avoid finger marks use suitable cloth. Remove the glass
by sliding the glass sideways out of the clamp and then
Removing Canterbury Fascia (refer FIG 18b)
1. Remove 4 M5 screws fixing the glass surround. To
remove glass surround pull it firmly towards you.
2. Remove the lower front cover by unscrewing two M5
screws through the air intake slots. Unit is fitted with
electronic switches. Ensure that the cable cannot be
trapped when the heater is installed.
3. Remove the surround by pulling the lower section
towards you gently to partly disengage it from the body
of the heater, then gently lift it vertically to completely
disengage it.
4. To fully remove the fascia, unclip the switch cable from
the PCB connector and unclip the cable from the clipping
points. The cable is routed through a plastic grommet
which will have to be removed from the base plate.
Refer
FIG 19
.
FIG 18a
Removing Fitzroy Fascia
FIG 18b
Removing Canterbury Fascia
To fully remove the fascia,
unclip the switch cable from
the cable connector on the
PCB and unclip the cable
from the clipping points on
the rear of the fascia.
Electrical Connection
This appliance is designed to operate on 240V AC power
supply. Failure to operate unit at correct supply voltage may
create unsafe conditions.
The heater is supplied with a flexible power cord with
a plug fitted. A 10 Amp switch socket MUST be located within
1.5m of the heater. For installations where the power point
is located outside of the enclosure, locate the power cord in
the fascia cut out on the left or right hand side as required.
For a power supply connection located inside the
enclosure, run the power cord through the cord access
located on the rear panel by pushing the cord access plate
from the bottom. The rubber grommet that is fitted over the
cord must be located correctly in the cut out of the cord
access plate. Refer
FIG 20
.
Restore the cord access plate to the original position and
seal with an appropriate removable material.
A suitable
double pole isolation switch MUST be installed
ELECTRICAL CONNECTION
Grommet
externally for servicing or emergency shut down
of the heater.
All fixed wiring MUST be installed by a suitably qualified
person and comply to the appropriate electrical wiring rules.
It is critical that the appliance is earthed and that the
active and neutral are not reversed. Issues arising
from incorrect electrical wiring at premises will not be
covered under warranty (including use of extension
cords). We recommend that the heater is connected
directly to a switch socket by its own power cord.
Refrain from using extension leads
.
FIG 19
3. To fully remove the fascia, unclip the switch cable from
14 | Cannon Power Flue
lifting out from the bottom. Place glass in a safe
position for refit later.
FIG 20
Fixing of the Fitzroy or Canterbury Fascia
You MUST NOT fix the front fascia to the wall.
The front fascia shall only be fixed to the heater.
Содержание Canterbury CANTIB-PDEE series
Страница 23: ...Cannon Power Flue 23 NOTES...
