background image

Cannon Power Flue | 5

SAFETY WARNINGS

                Please read this manual before installing and using  

the heater.

Safety Warnings

1.  

What to do if you smell gas

 

a.  Turn OFF the main gas supply 
b.  Extinguish any open flame 
c.  Open windows 
d.  Do not touch electrical switches 
e.  Do not use your telephone 
f.   Call your gas supplier immediately from  
  

a neighbour’s phone

2.  I mproper installation, adjustment, alteration, service 

or maintenance can cause injury or property damage. 
Refer to the sections of this manual for correct proce-
dures, or consult with place of purchase, a licensed 
plumber, a gas supplier or the Cannon distributor 
listed in this manual.

3.  I nstall the heater only in locations that are referred to 

in the installation instructions. Do not build the heater 
into bookcases, walls or enclosures (combustible 
materials) without the use of an insulating blanket & 
stand off brackets fitted (supplied with heater).

4.  Due to high temperatures the room heater should be 

located out of traffic and away from: 
•  Furniture and draperies 
•  Combustible materials 
•  Gasoline and other flammable liquids

 

Do

 

 not place clothing or other flammable

  

material on or near the heater.

5.  Keep curtains*, clothes, furniture and other  

flammable materials at least 900mm from front  
and sides of heater. 
* At the owner’s discretion curtain clearance can  

be less than 900mm as long as they are restrained 
from the front, top and sides of the heater.  
The manufacturer takes no responsibility if curtain 
clearance is less than 900mm and not restrained.

6.  C

  hildren and adults should be alerted to the hazard 
of high surface temperatures and should take care to 
avoid burns or clothing ignition.

 

Th is appliance is not intended for use by

  

persons (including children) with reduced

  

physical, sensory or mental capabilities or lack

 

of experience and knowledge, unless they have

 

been given supervision or instruction concerning

use of the appliance by a person responsible

 

for their safety. Children should be supervised to

 

ensure that they do not play with the appliance

.

7.  N

  ever attempt to burn paper or any other material in 
the heater.

8. 

  

  

 

9.  I f removed, the glass window must be put back onto 

the unit prior to operating the heater.

10. Installation and repairs must be performed by a 

licensed service person only, refer to back of manual 
for service number.

11. For installation into a non-combustible fireplace, i.e 

masonry or brick or into a mock fireplace, i.e. timber 
or plasterboard, the chimney and base should be  
of sound construction.

12. On first lighting your heater an odour and possibly 

some harmless smoke may be emitted due to its new 
condition. This is quite normal and will disappear after 
a few hours use.

Important: When this heater is operating the

 

mesh guard/glass front is hot. The mesh guard, or 
glass front is fitted to this appliance to reduce the 
risk of fire or injury from burns and no part of it 
should be permanently removed. For protection of 
young children or the infirm, a secondary guard is 
recommended (not supplied with heater).

This appliance meets the following standards: 
Standards Australia  
AS/NZS 3100 
AS/NZS 5601.1 
AS 4553:2008

DO NOT

 PLACE ARTICLES ON OR AGAINST THIS 

APPLIANCE.

DO NOT

 USE OR STORE FLAMMABLE 

MATERIALS NEAR THIS APPLIANCE.

DO NOT

 INSTALL OR USE THIS APPLIANCE IN 

MARINE CRAFT OR MOBILE HOMES.

DO NOT

 SPRAY AEROSOLS IN THE VICINITY OF 

THIS APPLIANCE WHILE IT IS IN OPERATION.

DO NOT

 MODIFY THIS APPLIANCE.

Содержание Canterbury CANTIB-PDEE series

























Отзывы: