CAME ZM3E, Руководство по установке

Страница: 16 / 24

p.
16
- M
an
ua
l
FA
010
80
-E
N
- 0
2/
20
18 - © C
AM
E S
.p
.A
. - T
ra
ns
la
tio
n o
f t
he o
rig
in
al i
ns
tru
ct
io
ns
Menu 1st level Menu 2nd level Options Default
Setting the number of motors from one to two depending on how many gate-
leaves the system has.
[Motor Type] [FROG] / [AXO] / [FAST] / [FERNI] / [FROG PLUS] [FROG]
Setting the type of operator for the swing gates on the system.
For AXO motors with cod. 001AX302304 and 001AX402306 set the slow-down
speed to the maximum value. The setting is in any case subject to an on-site
system-compliance inspection, pursuant to European Directive 2006/42/CE.
[Sleep Mode] [Disabled] / [Enabled] [Disabled]
For allowing the photocells to save energy in stand-by mode (with the RGP1
module connected).
[CRP Address]
[1]
……
[32]
[1]
With systems fitted with several operators and the CRP (Came Remote Protocol)
system connection, set an address between 1 and 32 for each control panel.
[CRP Baudrate ]
[1200] / [2400] / [4800] / [9600] / [19200] / [38400] /
[57600] / [115200]
[38400]
Setting the communication speed used in the CRP (Came Remote Protocol)
connection system.
[ENCODER]
& Only viewable if the corresponding function is selected in [Config] in the [FUNCTIONS] menu
[Sensitivity] [Enabled] / [Disabled] [Enabled]
Obstruction detection sensitivity.
[Swing Sens.]
[-
◦◦◦◦◦◦◦◦
+] [-
・◦◦◦◦◦◦◦
+]
Obstruction detection sensitivity during gate swing (both opening and closing).
&
You need to enable the [Sensitivity] in the [ENCODER] menu .
[Slodwn. Sens.] [-
◦◦◦◦◦◦◦◦
+] [-
・◦◦◦◦◦◦◦
+]
Obstruction detection sensitivity during slow-down (both opening and closing).
& You need to enable the
[Enc. Slodwn.] function
in the
[ENCODER] menu
.
[Enc. Slwdwn.] [ON] / [OFF] [ON]
Enabling the opening and closing slow-down starting points.
[M1 Op. SloDwn.
%]
[1%]
……
[60%] [10%]
Setting the starting slow-down of M1 before the opening limit-switch point,
calculated as a percentage (from 1% to 60% of the full leaf-swing).
& This function only appears if the
[Enc. Slodwn.] function is enabled
in the
[ENCODER] menu
.
[M1 Slow. CH %] [1%]
……
[60%]
[10%]
Setting the starting slow-down of M1 before the closing limit-switch point,
calculated as a percentage (from 1% to 60% of the full leaf-swing).
&
This function only appears if the [Enc. Slodwn.] function is enabled in the
[ENCODER] menu
.
[M2 Appr. AP %] [1%]
……
[60%]
[10%]
Setting the starting slow-down of M2 before the opening limit-switch point,
calculated as a percentage (from 1% to 60% of the full leaf-swing).
&
This function only appears if the [Enc. Slodwn.] function is enabled in the
[ENCODER] menu .
[M2 Slow. CH %] [1%]
……
[60%]
[10%]