EN
I-MPC Rev1 - Operating Instructions
Page 11 / 88
THIS INSTRUCTION MANUAL IS THE PROPERTY
OF CALPEDA S.P.A. ANY REPRODUCTION, EVEN
IF PARTIAL, IS FORBIDDEN
1. GENERAL INFORMATION
Before using the product carefully read the information
contained in this instruction manual, the manual should
be kept for future reference.
Italian is the original language of this instruction
manual, this language is the reference language in
case of discrepancies in the translations.
This manual is part of the essential safety requirement
and must be retained until the product is finally de-
commissioned.
The customer, in case of loss, can request a copy
of the manual by contacting Calpeda S.p.A. or their
agent, specifying the type of product data shown on
the label of the machine (see 2.3 Marking)
Any changes, alterations or modifications made to the
product or part of it, not authorized by the manufacturer,
will revoke the “CE declaration” and warranty.
This appliance should not be operated
by children younger than 8 years, people
with reduced physical, sensory or mental
capacities, or inexperienced people who
are not familiar with the product, unless
they are given close supervision or
instructions on how to use it safely and
are made aware by a responsible person
of the dangers its use might entail.
Children must not play with the appliance.
It is the user's responsibility to clean
and maintain the appliance. Children
should never clean or maintain it
unless they are given supervision.
Read carefully the installation section
which sets forth:
- The maximum permissible structural
working pressure (Chapter 3.1).
- The type and section of the power
cable (Chapter 6.5).
- The type of electrical protection to be
installed (Chapter 6.5).
1.1. Symbols
To improve the understanding of the manual, below are
indicated the symbols used with the related meaning.
Information and warnings that must be
observed, otherwise there is a risk that the
machine could damage or compromise
personnel safety.
The failure to observe electrical information
and warnings, could damage the machine or
compromise personnel safety.
i
Notes and warnings for the correct management
of the machine and its parts.
Operations that could be performed by the final
user. After carefully reading of the instructions,
is responsible for maintenance under normal
conditions. They are authorized to affect
standard maintenance operations.
Operations that must be performed by a
qualified electrician. Specialized technician
authorised to affect all electrical operations
including maintenance. They are able to
operate with in the presence of high voltages.
Operations that must be done performed by
a qualified technician. Specialized technician
able to install the device, under normal
conditions, working during “maintenance”,
and allowed to do electrical and mechanical
interventions for maintenance. They must
be capable of executing simple electrical
and mechanical operations related to the
maintenance of the device.
Indicates that it is mandatory to use individual
protection devices.
OFF
Operations that must be done with the device
switched off and disconnected from the power
supply.
ON
Operations that must be done with the device
switched on.
1.2. Manufacturer name and address
Manufacturer name: Calpeda S.p.A.
Address: Via Roggia di Mezzo, 39
36050 Montorso Vicentino - Vicenza / Italia
www.calpeda.it
1.3. Authorized operators
The product is intended for use by expert operators
divided into end users and specialized technicians.
(see the symbols above).
i
It’s forbidden, for the end user, carry out
operations which must be done only by
specialized technicians. The manufacturer
declines any liability for damage related to the
non-compliance of this warning.
SUMMARY
1. GENERAL INFORMATION ........................... 11
2. TECHNICAL DESCRIPTION ........................12
3. TECHNICAL FEATURES ..............................12
4. SAFETY ........................................................13
5. TRANSPORTATION AND HANDLING .........13
6. INSTALLATION .............................................13
7. PROGRAMMING GUIDE..............................14
8. STARTUP AND OPERATION .......................15
9. MAINTENANCE ............................................16
10. DISPOSAL ....................................................17
11. SPARE PARTS .............................................18
12. ESIGNATION OF PARTS .............................18
13. ALARMS .......................................................18
14. TROUBLESHOOTING ..................................19
15 Pump located below the water level .............82
14 Pump located above the water level .............84
17 Drawing for dismantling and assembly .........86
Declaration of conformity .......................................88
