California Instruments 3000iL Скачать руководство пользователя страница 42

Страница: 42 / 100

iL Series User Manual

Rev B

California Instruments

Input

Press this key to select the input coupling for the meter function.
The parameter selections allow the meter functions to display
measurements that include AC components only, DC
components only, or AC+DC components.

Display

Command Function

INP:COUP
<char>

Choose meter coupling (AC, DC or ACDC)

WINDOW <char>

Select harmonic measurement window meter (KBESSEL
or RECT)

CURR:RANG
<char>

Choose current meter range (HIGH or LOW) 4801iL only

Shift Harmonic

Press this key to access the harmonic menu list.

Display

Measurement

<reading>A I:MAG:<index>

current harmonic magnitude

<reading>º I:PHASE:<index>

current harmonic phase

<reading>V V:MAG:<index>

voltage harmonic magnitude

<reading>º V:PHASE:<index>

voltage harmonic phase

<reading>A N:MAG:<index>

neutral current harmonic magnitude

<reading>º N:PHASE:<index>

neutral current harmonic phase

<reading> CURR:THD

current total % harmonic distortion

<reading> VOLT:THD

voltage total % harmonic distortion

Table 16 : Harmonic measurement display readouts

4.4.4 Output Control Keys

Output control keys control the output functions of the AC source.

Voltage

Press this key to access the voltage menu list.

Display

Command Function

Phase
selectable

VOLT <value>

Set immediate AC output voltage.

yes

VOLT:T <value>

Set triggered output voltage.

yes

VOLT:M <char>

Select the voltage mode.
(FIXED, STEP, PULSE or LIST)

yes

RANGE <char>

Select the voltage range (150 or 300).

yes

SLEW <value>

Set immediate voltage slew rate in
volts/second.

yes

SLEW:T <value>

Set triggered voltage slew rate in volts/second.

yes

SLEW:M <char>

Select the voltage slew mode.
(FIXED, STEP, PULSE or LIST)

yes

ALC <char>

Select the voltage sense source (INT or EXT).

ALC:DET <char>

Select voltage control mode (RMS or RTIME)
4801iL only.

Table 17 : Output control display readouts

Содержание 3000iL




































































































Результаты поиска

Содержание 3000iL

Отзывы:

Похожие инструкции для 3000iL

Бренды по названию

Популярные бренды

California Instruments 3000iL, Руководство пользователя

Результаты поиска

Содержание 3000iL

Отзывы:

Похожие инструкции для 3000iL

Бренды по названию

Популярные бренды