Cabletron Systems 9A426-01 Скачать руководство пользователя | Manualshive

Страница: 4 / 50

background image

Notice

ii

FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment uses, generates, and can radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.

WARNING:

Changes or modifications made to this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

VCCI Notice

This equipment is in the 1st Class Category (information equipment to be used in commercial and/or
industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial
and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be
caused to radios and TV receivers, etc.

Read the instructions for correct handling.

«
...
2
3
4
5
6
...
»

Содержание 9A426-01



















































Отзывы:

Нет отзывов

Похожие инструкции для 9A426-01

Бренд: Yamaha Страницы: 4

Бренд: Oracle Страницы: 112

Бренд: APARIAN Страницы: 2

PCI-6110E/6111E

Бренд: National Instruments Страницы: 113

InvenSense RoboKit1

Бренд: TDK Страницы: 13

Бренд: FDI Страницы: 2

Бренд: Sangoma Страницы: 6

Бренд: PMD Страницы: 74

Бренд: BHU NETWORKS Страницы: 75

REJ06B0734-0100

Бренд: Renesas Страницы: 19

Бренд: Westermo Страницы: 34

Бренд: Compal Страницы: 47

Бренд: ETAS Страницы: 84

MP5S Plus Writer

Бренд: SONIX Страницы: 23

Бренд: Alcatel Страницы: 4

Internet Security Appliances

Бренд: SonicWALL Страницы: 293

Бренд: TP-Link Страницы: 182

Router 3000 Series

Бренд: 3Com Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды