Cabletron Systems 9A426-01 Скачать руководство пользователя | Manualshive

Страница: 35 / 50

background image

3-1

Chapter 3

Operation

The 9A426-01 Module has two fixed network interface connections: the module’s
ATM interface, and the module’s INB interface. Both interfaces connect to the
module’s SmartSwitch ASIC core.

In addition to fixed interface connections, the module offers a user-configurable
FNB interface. Through Local Management or SNMP, you can connect the
module’s SmartSwitch ASIC core to one (or none) of the two FNB interfaces (FNB-
1 or FNB-2). Keep in mind that connecting the module’s SmartSwitch ASIC core
to an FNB interface also connects the selected FNB to the module’s three fixed
interface connections (the two front panel ATM ports and the INB interface).

As shown in Figure 3-1, packets can be received simultaneously at the ATM
interface, the INB interface and, if configured by the user, one of the FNB
interfaces (FNB-1 or FNB-2). All packets that enter the module are converted into
a common format known as a canonical frame. The SmartSwitch ASIC core’s
circuitry determines the interfaces to which the frames are forwarded.

«
...
33
34
35
36
37
...
»

Содержание 9A426-01



















































Отзывы:

Нет отзывов

Похожие инструкции для 9A426-01

Бренд: Linksys Страницы: 2

Бренд: DBM Страницы: 50

Бренд: IBM Страницы: 32

Бренд: Xinje Страницы: 57

SCSI PC Card REX-9530V

Бренд: Ratoc Systems Страницы: 30

Бренд: Delta Electronics Страницы: 1

Бренд: TRENDnet Страницы: 2

IE-SW-VL16-14TX-2SC

Бренд: Weidmuller Страницы: 17

Бренд: Watchguard Страницы: 40

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

Бренд: Keithley Страницы: 98

Бренд: Rosewill Страницы: 3

Бренд: Dantel Страницы: 62

Бренд: Daedalon Страницы: 6

Бренд: ProCurve Страницы: 2

EK-Loop Modulus Series

Бренд: ekwb Страницы: 7

Бренд: National Instruments Страницы: 80

Бренд: Advantech Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды