Cabletron Systems 9A426-01 Скачать руководство пользователя | Manualshive

Страница: 17 / 50

background image

2-1

Chapter 2

Preparing and Installing the
9A426-01 Module

This chapter describes the physical layout of the 9A426-01 Module and explains
how to prepare and install the module in a SmartSwitch 9000 chassis.

Unpacking the Module

1. Carefully remove the module from the shipping box. (Save the box and

packing materials in the event the module must be reshipped.)

2. Remove the module from the plastic bag. Observe all precautions to prevent

damage from Electrostatic Discharge (ESD).

3. Carefully examine the module, checking for damage. If any damage exists,

DO NOT install the module. Contact Cabletron Systems Technical Support
immediately.

Never expose the module’s components to Electrostatic Discharge: Make sure you
have attached the module’s disposable grounding strap to your wrist and always
place the module on a non-conductive surface.

WARNING

«
...
15
16
17
18
19
...
»

Содержание 9A426-01



















































Отзывы:

Нет отзывов

Похожие инструкции для 9A426-01

Бренд: Paradyne Страницы: 22

Бренд: Panasonic Страницы: 44

HAWA-Frontside 60/B

Бренд: hawa Страницы: 28

Бренд: Belkin Страницы: 72

Бренд: Helmholz Страницы: 28

Бренд: Phytec Страницы: 53

Бренд: ZyXEL Communications Страницы: 2

Бренд: Dahua Страницы: 24

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Бренд: Avolites Страницы: 24

Бренд: ZyXEL Communications Страницы: 485

Бренд: Justec Страницы: 61

Бренд: Macsense Страницы: 13

Бренд: 3Ware Страницы: 4

Duinotech Lilypad Plus XC3920

Бренд: Jaycar Electronics Страницы: 2

Digital Encoder Plus

Бренд: IDT Страницы: 98

TeleCLIENT TC7730 Series

Бренд: ETL Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды