Cabletron Systems 9A426-01 Скачать руководство пользователя

Страница: 42 / 50

LANVIEW LEDs

4-2

The functions of the

System Status (SMB and CPU) LEDs

, are listed in

Table 4-1.

The status of the INB Receive LED is listed in Table 4-2.

Table 4-1. System Status (SMB and CPU) LEDs

LED Color

State

Description

Green

Functional

Fully operational

Yellow/Green

Booting

Blinks yellow and green while booting

Yellow

Testing

Performing power-up testing

Yellow (Flashing)

Crippled

Not fully operational (i.e., one bad port)

Red

Reset

Normal power-up reset

Red (Flashing)

Failed

Fatal error has occurred

Off

No Power

No power is being supplied to the module

Table 4-2. INB Receive LED

LED Color

State

Green

Link exists, no activity, port is enabled

Yellow (Flashing)

Link exists, activity, port is enabled

Red

No link, port is disabled

Red (Flashing)

Link exists, port is disabled

Off

No link, no activity, port is enabled

Содержание 9A426-01



















































Результаты поиска

Содержание 9A426-01

Отзывы:

Похожие инструкции для 9A426-01

Бренды по названию

Популярные бренды

Cabletron Systems 9A426-01, Руководство пользователя

Результаты поиска

Содержание 9A426-01

Отзывы:

Похожие инструкции для 9A426-01

Бренды по названию

Популярные бренды