BYD G3 AUTO Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 160

background image

BYD G3 AUTO Owner’s Manual

132

Check Engine Oil Level

Shut down engine at operating
temperature, and check engine oil
level with dipstick.

1. To get accurate reading, you shall

pack the car on flat ground. Shut
down the engine and wait for a few
minutes so that engine oil is collected
at the bottom of the engine.

2. Pull out the dipstick, place a piece of

fabric at its end and wipe it clean.

3. Insert the dipstick again. You shall

insert it to the bottommost position for
accurate reading.

4. Pull out the dipstick, place a piece of

fabric at its end and check the engine
oil level.

Note

Do not drop engine oil on parts of
the car.

If the oil level is near the low oil line,
you shall add additional engine oil of
the same type in the engine.

Remove the engine oil fill cap, add a
small amount of engine oil and then
check the dipstick. You are
recommended to use funnel when
adding engine oil.
After adding engine oil, the oil level shall
be located between the low oil line and
high oil line on the dipstick as shown in
the figure above.
When the oil level is proper, install the fill
cap and tighten it manually.

Note

◆

Do not splash engine oil on

parts of the car.

◆

Do not add too much oil, or

engine may be damaged.

◆

Check the oil level with

dipstick after you finish adding
engine oil.

Engine Oil Specification

Only use lubricating oil approved by
BYD-authorized service stations or
equivalents in compliance with the
following grade and viscosity.

Engine Oil Grade for Gasoline Engine:

SAE 5W—30 above -30

℃

SAE 15W—40 above -15

℃

API Grade SG or above
Amount: 3L (liter)

Low level

High level

Oil filling

Correct

Overfull

«
...
136
137
138
139
140
...
»

Содержание G3 AUTO

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G3 AUTO

Бренд: Kia Страницы: 385

Бренд: Trailboss Страницы: 5

Бренд: REVCAMUK Страницы: 4

PRIME DESIGN VRR-NV200

Бренд: Safe Fleet Страницы: 12

Бренд: Ecco Страницы: 9

Бренд: Anker Technology Страницы: 8

Бренд: Edelbrock Страницы: 2

Бренд: Mercedes-Benz Страницы: 93

Бренд: Prorack Страницы: 13

T13 Outback Frontal Protection System

Бренд: T.J.M. Страницы: 18

Бренд: Audi Страницы: 4

Бренд: Westin Страницы: 3

Бренд: Brainz Страницы: 2

Бренд: Reese Страницы: 21

Бренд: Porsche Страницы: 1005

Бренд: Ace K9 Страницы: 14

Бренд: Buick Страницы: 475

Бренд: Volvo Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды