Butler SPEEDLINER 8050WS Скачать руководство пользователя | Manualshive

Страница: 6 / 53

background image

Instruction manual

SPEEDLINER 8050WS - SPEEDLINER 9080WS

Code M0205 - rev.1.0

(11/2010)

BUTLER S.p.A.

Page 4/51

BUTLER Engineering & Marketing S.p.A. a s.u. -

Via Balduina 5/7 - 42010 Rio Saliceto (RE - Italy)

Tel. +39 0522 647911, Fax +39 0522 649760

e-mail: [email protected] / www.butler.it

1 INTENDED

USE

SPEEDLINER 8050WS and SPEEDLINER 9080WS systems are machines for the detection

of all vehicle special angles.
Angles are detected by four detectors with microprocessor technology and infrared

measurement system, and data transmission (without any cable connection between

detectors).
The data of front cabin detectors are transmitted VIA RADIO through modules

.

Vehicle max. allowed wheelbase length for data transmission and angle measurement is 4.5
m.

Machine operational temperature range: 0 to 40°C.

2 OPERATOR

TRAINING

The machine must be used by specifically trained and authorised personnel, only. To ensure
proper machine use and that measurements can be efficiently taken, operators must be correctly

trained and acquire the skills consistent with the instructions provided by the manufacturer. In
case of any doubts relating to machine use and maintenance, refer to the instruction manual and
then, if such doubts persist, contact an authorised after-sales centre or BUTLER S.p.A. technical

assistance directly.

2.1 General Preventive Measures



During operation and maintenance of this machine, always abide by the safety and

accident-prevention regulations in force.



The machine must only be used by adequately trained and authorised persons.



This machine must only be used for the purpose for which it was expressly intended.

BUTLER S.p.A. declines all liability for injury or damage to persons animals and

things caused by improper machine use.



Accessories and spare parts must be fitted by persons authorised by BUTLER S.p.A.

and only original spare parts and accessories must be used.



The machine must only be operated in places where there is no danger of explosions

or fire.



Removal or changes made to safety devices, or warning signals on the machine can

cause serious hazards and represent a violation of European safety regulations.



Before doing any maintenance jobs on the system, always disconnect the power

supply.
In case of doubt, do not interpret, but contact BUTLER S.p.A. technical assistance in

order to obtain instructions suitable for performing operations in total safety.



Do not allow unauthorised personnel to come near the wheel aligner during use.

«
...
4
5
6
7
8
...
»

Содержание SPEEDLINER 8050WS






















































Отзывы:

Нет отзывов

Похожие инструкции для SPEEDLINER 8050WS

Бренд: Hofmann Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды