Butler SPEEDLINER 8050WS Скачать руководство пользователя

Страница: 12 / 53

Instruction manual

SPEEDLINER 8050WS - SPEEDLINER 9080WS

Code M0205 - rev.1.0

(11/2010)

BUTLER S.p.A.

Page 10/51

BUTLER Engineering & Marketing S.p.A. a s.u. -

Via Balduina 5/7 - 42010 Rio Saliceto (RE - Italy)

Tel. +39 0522 647911, Fax +39 0522 649760

e-mail: [email protected] / www.butler.it

3.7.3 Detector Keypads

Figure 4

KEYS DESCRIPTION

Detector switch-on key.

If pressed at the same time, they allow detector

manual switching off.

Legend of Figure 4:

A -



Green LED on:

detector battery is under charge

B -



Red LED steady on:

detector is on



Red LED flashing:

detector is flat (when battery residual charge is

lower than or equal to 30%); it will turn off after
a few minutes

3.7.4 LED indicating Levelling and Tolerance during Adjustment

Detectors series SPEEDLINER 8050WS and SPEEDLINER 9080WS (see par.3.7.1 and 3.7.2)

are equipped with LED indicators for their correct levelling (for levelling function in detectors

SPEEDLINER 9080WS a display is used, see par. 3.7.3) and for tolerance during adjustment..

Levelling indicator



RED LED on



detector is not levelled



RED LED flashing and GREEN LED steady on



detector is close, but not levelled



GREEN LED ONLY is flashing



detector is levelled



RED LED flashing and GREEN LED steady on



detector is close, but not levelled



RED LED on



detector is not levelled

Tolerance indicator during adjustment



GREEN LED flashing



measurement is within tolerance, exactly at the centre



RED LED flashing and GREEN LED steady on



measurement is within

tolerance



RED LED on



measurement is NOT within tolerance

Note: during front adjustment, if you want to observe tolerance onto LEDs, take the red selection

frame on the value you are adjusting (see 8.12 on page 36).
During rear adjustment, on the contrary, tolerance is indicated both on horizontal LEDs (toe) and

vertical LEDs (camber).

LEDs on

FRONT

detectors

Tolerance

TOE or

CAMBER or

CASTER

LEDs on

REAR

detectors

TOE tolerance

Levelling (SL8050WS, only)
CAMBER tolerance

Alphanumeric display (mod. SL9080WS,
ONLY) - It shows :
- battery charge in %
- electronic level in the relevant phase

- Run-Out status in the relevant

phase

(A) Green LED

(B) Red LED

Содержание SPEEDLINER 8050WS






















































Результаты поиска

Содержание SPEEDLINER 8050WS

Отзывы:

Похожие инструкции для SPEEDLINER 8050WS

Бренды по названию

Популярные бренды

Butler SPEEDLINER 8050WS, Инструкция по эксплуатации

Результаты поиска

Содержание SPEEDLINER 8050WS

Отзывы:

Похожие инструкции для SPEEDLINER 8050WS

Бренды по названию

Популярные бренды