Burford 2200M Скачать руководство пользователя страница 137

Страница: 137 / 214

Troubleshooting

133

Error Code: E146

Belt Motor Fuse Blown, Motor Stalled, or Bad Encoder

These error codes are set when the controller is trying to move the belt motor, but the motor

either isn't moving or the controller cannot tell that the motor is moving..

With power off, check to see if

belt motor is jammed or is hard

to turn by hand.

Check for a blown

Belt Motor Fuse on

the AMP Board.

See Section 4.6.3.

Clear out jam, loosen

belt, or replace

bearings as needed.

Replace Belt Motor Fuse on AMP board and test for

proper operation. Watch belt motor during startup.

Note: Belts will not run until motors 1 – 3 complete

their homing sequence.

Cycle power, start tyer

and see if belt motor

moves at all before

error occurs.

Place voltmeter leads

across motor power

supply connector

(T1) on edge of AMP

board. Start tyer.

Check for DC

motor voltage on

AMP board. Note:

This may be

difficult to measure

if the DC power

contactor drops out

quickly.

Check motor supply circuit breaker

in the central cabinet.

Use Section 4.6.2 to troubleshoot motor connections.

Repair connection

in belt motor

wiring.

Replace

Belt

motor.

Fuse OK

Belt Motor driver
on AMP board is

bad. Replace the

AMP board.

Belt motor leads

are backward.

Reverse wires at

AMP board.

SAFETY WARNING

The following troubleshooting procedure may require that tests be made with the

electrical enclosures open and power turned ON. These tests should only be conducted

by authorized personnel who are aware of the electrical and mechanical hazards present.

Motor is

hard to

turn

Motor

turns

easily

Troubleshoot

DC latch circuit.

The problem is

with the power supply

or wiring to them.

Reset
circuit

breaker

Check voltage at

power supply

48 volt DC

Breaker OK

DC contactor pulls

in, and motor voltage

is present

DC contactor

pulls

in , but motor

voltage

is not present

Belt motor does

not turn at all

Belt's first move

is forward

Continued on

Belt's first move

is backward.

DC contactor

never pulls in

DC Power

not present

Breaker tripped

Fuse blows

immediately

Bad

connection

Motor and

connections OK

Bad motor

Fuse Bad

Flow Chart 0-27 Error Code: E146

Содержание 2200M






















































































































































































































Результаты поиска

Содержание 2200M

Отзывы:

Похожие инструкции для 2200M

Бренды по названию

Популярные бренды

Burford 2200M, Руководство пользователя

Результаты поиска

Содержание 2200M

Отзывы:

Похожие инструкции для 2200M

Бренды по названию

Популярные бренды