Bull DPS7000/XTANOVASCALE 7000 180Rb 7 Скачать руководство пользователя страница 91

Страница: 91 / 258

Configuring Your System 3-31

Figure 3-4. FRU Manager Main Window

Table 3-6. FRU Manager Menus

Menu

Options

File

Open FRU

: Opens FRU data from a previously saved file.

Save FRU

: Saves FRU data to a file in binary raw or verbose text format.

Exit

: Quits the FRU Manager.

View

FRU Info

: Displays FRU information of the selected device.

All FRU Areas

: Displays FRU areas of all devices.

By Device Type

: Displays FRU areas sorted by device type.

Settings

Display Hex

: Displays FRU areas in hex format.

Display Verbose

: Displays FRU areas in verbose format.

Output Text

: Saves FRU data in verbose format.

Output Binary

: Saves FRU data in binary format

Help

About

: Displays FRU Manager version information.

Exiting the SSU

Exiting the SSU causes all windows to close.

Exit the SSU by opening the menu bar item File in the SSU Main window.

Click <Exit>.
Or
Highlight Exit, and press <Enter>.

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7



































































































































































































































































Результаты поиска

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7

Отзывы:

Bull DPS7000/XTANOVASCALE 7000 180Rb 7, Руководство по обслуживанию, Страница: 91 / 258

Результаты поиска

Содержание DPS7000/XTANOVASCALE 7000 180Rb 7

Отзывы: